Read Sony MEX-BT5700U / MEX-BT5750U Service Manual online
MEX-BT5700U/BT5750U
11
(MEX-BT5750U)
Precauciones
Asegúrese de instalar la unidad en el tablero del
automóvil, ya que la parte posterior de la unidad se
calienta durante el uso.
automóvil, ya que la parte posterior de la unidad se
calienta durante el uso.
• Esta unidad ha sido diseñada para alimentarse sólo con cc
de 12 V de masa negativa.
• No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los raíles del asiento).
• Antes de realizar las conexiones, apague el automóvil para
evitar cortocircuitos.
• Conecte los cables de fuente de alimentación amarillo y
rojo solamente después de haber conectado los demás.
• Conecte todos los cables de conexión a masa a
un punto común.
• Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
• No cubra las ranuras ni las rejillas de ventilación de la
unidad.
Notas sobre el cable de fuente de alimentación
(amarillo)
• Cuando conecte esta unidad en combinación con otros
(amarillo)
• Cuando conecte esta unidad en combinación con otros
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
conectado del automóvil debe ser superior a la suma del
fusible de cada componente.
• Si no hay circuitos del automóvil con capacidad nominal
suficientemente alta, conecte la unidad directamente a la
batería.
batería.
Ejemplo de conexiones
Notas (
-A)
• Asegúrese de conectar primero el cable de conexión a masa antes
de realizar la conexión del amplificador.
• La alarma sonará únicamente si se utiliza el amplificador
incorporado.
L
R
FRONT
AUDIO OUT
REAR
AUDIO OUT
BUS
CONTROL IN
MIC IN
REMOTE
IN
REAR
AUDIO OUT
FRONT
BUS
IN
SUB OUT (MONO)
BUS AUDIO IN
Cautions
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.
as the rear side of the unit becomes hot during use.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• Do not cover the ventilation slots or heat sinks of the
unit.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Connection example
Notes (
-A)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Tip (
-B)
When connecting only a single CD changer or other optional
device, connect directly to this unit.
device, connect directly to this unit.
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow, and red power supply leads.
yellow, and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
supply leads.”
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
system may damage the unit.
To the interface cable of a car telephone
To a car’s illumination signal
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
surface of the car first.
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
supply leads.”
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
If speaker and amplifier are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
A
AMP REM
Red
Rojo
Rojo
Yellow
Amarillo
Amarillo
ANT REM
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
*
1
from car antenna (aerial)
desde la antena del automóvil
desde la antena del automóvil
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
White
Blanco
Blanco
White/black striped
Con rayas blancas y negras
Con rayas blancas y negras
Gray
Gris
Gris
Gray/black striped
Con rayas grises y negras
Con rayas grises y negras
Green
Verde
Verde
Green/black striped
Con rayas verdes y negras
Con rayas verdes y negras
Purple
Morado
Morado
Purple/black striped
Con rayas moradas y negras
Con rayas moradas y negras
Black
Negro
Negro
Blue
Azul
Azul
Blue/white striped
Con rayas azules y blancas
Con rayas azules y blancas
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
Corriente máx. de alimentación de 0,3 A
Sugerencia (
-B)
Cuando conecte un solo cambiador de CD u otro dispositivo
opcional, hágalo directamente a esta unidad.
opcional, hágalo directamente a esta unidad.
Diagrama de conexión
A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después
los cables amarillo y rojo de fuente de alimentación.
los cables amarillo y rojo de fuente de alimentación.
Al cable de control de la antena motorizada o al
cable de fuente de alimentación del amplificador
de señal de la antena
de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplificador
• Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
manualmente, no será necesario conectar este cable.
• Si el automóvil incorpora una antena de FM/AM en el cristal
trasero o lateral, consulte “Notas sobre los cables de control y
de fuente de alimentación”.
de fuente de alimentación”.
A AMP REMOTE IN de un amplificador de
potencia opcional
Esta conexión es sólo para amplificadores. La conexión de
cualquier otro sistema puede dañar la unidad.
cualquier otro sistema puede dañar la unidad.
Al cable de interfaz de un teléfono para
automóvil
A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
negro a una superficie metálica del automóvil.
Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio del
interruptor de encendido
interruptor de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/AM en el cristal
trasero o lateral, consulte “Notas sobre los cables de control y
de fuente de alimentación”.
de fuente de alimentación”.
Al terminal de alimentación de +12 V que recibe
energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
• El cable de control de la antena motorizada (azul) suministrará cc
• El cable de control de la antena motorizada (azul) suministrará cc
de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/AM incorporada en
el cristal trasero o lateral, conecte el cable de control de antena
motorizada (azul) o el cable de fuente de alimentación auxiliar
(rojo) al terminal de alimentación del amplificador de antena
existente. Para obtener más información, consulte a su distribuidor.
motorizada (azul) o el cable de fuente de alimentación auxiliar
(rojo) al terminal de alimentación del amplificador de antena
existente. Para obtener más información, consulte a su distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación de la
• Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
• Utilice altavoces con una impedancia de 4 a 8
? con la capacidad
de potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
• No conecte el cable de conexión a masa de esta unidad al terminal
negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces activos
• Conecte solamente altavoces pasivos. Si conecta altavoces activos
(con amplificadores incorporados) a los terminales de altavoz,
puede dañar la unidad.
puede dañar la unidad.
• Para evitar fallas de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si la unidad comparte un
cable negativo común (–) para los altavoces derecho e izquierdo.
cable negativo común (–) para los altavoces derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “Failure” en la pantalla. Si es así, compruebe la conexión
de ambos dispositivos.
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “Failure” en la pantalla. Si es así, compruebe la conexión
de ambos dispositivos.
Left
Izquierdo
Izquierdo
Right
Derecho
Derecho
*
3
*
1
RCA pin cord (not supplied)
*
2
Supplied with the CD changer
*
3
Insert with the cord upwards.
*
4
For details on installing the
microphone, see the supplied
instructions manual of the
XA-MC10.
microphone, see the supplied
instructions manual of the
XA-MC10.
*
1
Cable con terminales RCA
(no suministrado)
(no suministrado)
*
2
Suministrado con el cambiador de
CD
CD
*
3
Insertar con el cable hacia arriba.
*
4
Para obtener detalles acerca de la
instalación del micrófono, consulte el
manual de instrucciones del
XA-MC10.
instalación del micrófono, consulte el
manual de instrucciones del
XA-MC10.
FRONT
AUDIO OUT
REAR
AUDIO OUT
SUB OUT (MONO)
BUS AUDIO IN
BUS CONTROL IN
B
Orange/white striped
Con rayas naranjas y blancas
Con rayas naranjas y blancas
Light blue
Azul celeste
Azul celeste
ATT
ILLUMINATION
*
1
*
2
*
4
Click on the first or last page to see other MEX-BT5700U / MEX-BT5750U service manuals if exist.