Read Sony MEX-BT5100 Service Manual online
MEX-BT5100
9
(US, Canadian, E)
A
B
SUB OUT (MONO)
AUDIO OUT
REAR
AUDIO OUT
FRONT
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Sélecteur de source*
Selector de fuente*
XA-C40
* not supplied
non
non
fourni
no
suministrado
Cautions
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.
as the rear side of the unit becomes hot during use.
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all ground leads to a common ground
point.
• Be sure to in su late any loose un con nect ed leads with
electrical tape for safety.
• Do not cover the ventilation slots or heat sinks of the
unit.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
• When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
L
R
AUDIO
OUT
REAR
AUDIO
OUT
FRONT
BUS
AUDIO
IN
2
4
5
6
7
1
3
AUDIO OUT
FRONT
BUS AUDIO IN
/AUX IN
*
2
BUS
CONTROL IN
REMOTE
IN
AUDIO OUT
REAR
SUB OUT (MONO)
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Corriente máx. de alimentación de 0,3 A
Courant max. fourni 0,3 A
Corriente máx. de alimentación de 0,3 A
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
Rayé bleu/blanc
Con rayas azules y blancas
Rayé bleu/blanc
Con rayas azules y blancas
ANT REM
ʔ
*
1
Red
Rouge
Rojo
Rouge
Rojo
Yellow
Jaune
Amarillo
Jaune
Amarillo
Black
Noir
Negro
Noir
Negro
Blue
Bleu
Azul
Bleu
Azul
White
Blanc
Blanco
Blanc
Blanco
Green
Vert
Verde
Vert
Verde
Purple
Mauve
Morado
Mauve
Morado
White/black striped
Rayé blanc/noir
Con rayas blancas y negras
Rayé blanc/noir
Con rayas blancas y negras
Gray/black striped
Rayé gris/noir
Con rayas grises y negras
Rayé gris/noir
Con rayas grises y negras
Green/black striped
Rayé vert/noir
Con rayas verdes y negras
Rayé vert/noir
Con rayas verdes y negras
Gray
Gris
Gris
Gris
Gris
Left
Gauche
Izquierdo
Gauche
Izquierdo
Right
Droit
Derecho
Droit
Derecho
Left
Gauche
Izquierdo
Gauche
Izquierdo
Right
Droit
Derecho
Droit
Derecho
Purple/black striped
Rayé mauve/noir
Con rayas moradas y negras
Rayé mauve/noir
Con rayas moradas y negras
*
1
Source selector
(not supplied)
Sélecteur de source
(non fourni)
Selector de fuente
(no suministrado)
XA-C40
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
Suministrado con el cambiador de CD/MD
Fourni avec le changeur de CD/MD
Suministrado con el cambiador de CD/MD
*
6
Max. supply current 0.1 A
Courant max. fourni 0,1 A
Courant max. fourni 0,1 A
Corriente máx. de alimentación de 0,1 A
ILLUMINATION
Light blue
Bleu ciel
Azul celeste
Bleu ciel
Azul celeste
Orange/white striped
Rayé orange/blanc
Con rayas naranjas y blancas
Rayé orange/blanc
Con rayas naranjas y blancas
ATT
from car antenna
à partir de l’antenne de la voiture
desde la antena del automóvil
à partir de l’antenne de la voiture
desde la antena del automóvil
*
1
RCA pin cord (not supplied)
*
2
Be sure to match the color-coded
cord for audio to the appropriate
jacks from the unit. If you connect
an optional CD/MD changer, you
cannot use AUX IN terminal.
jacks from the unit. If you connect
an optional CD/MD changer, you
cannot use AUX IN terminal.
*
3
Auxiliary optional equipment
such as portable DVD player (not
supplied)
supplied)
*
4
Supplied with the auxiliary
equipment
*
5
Supplied with XA-C40
*
6
Insert with the cord upwards.
*
1
Cordon à broche RCA (non fourni)
*
2
Veillez à faire correspondre le code
de couleur du cordon audio à celui
des fi ches correspondantes de
l’appareil. Si vous raccordez un
changeur de CD/MD en option,
vous ne pouvez pas utiliser la
borne AUX IN.
des fi ches correspondantes de
l’appareil. Si vous raccordez un
changeur de CD/MD en option,
vous ne pouvez pas utiliser la
borne AUX IN.
*
3
Appareil auxiliaire en option,
par exemple un lecteur de DVD
portable (non fourni)
portable (non fourni)
*
4
Fourni avec l’appareil auxiliaire
*
5
Fourni avec le XA-C40
*
6
Insérez avec le câble vers le haut.
*
1
Cable con terminales RCA
(no suministrado)
*
2
Asegúrese de hacer coincidir
el cable de audio codifi cado
con colores con las tomas
correspondientes de la unidad. Si
conecta un cambiador de CD/MD
opcional, no podrá utilizar el
terminal AUX IN.
con colores con las tomas
correspondientes de la unidad. Si
conecta un cambiador de CD/MD
opcional, no podrá utilizar el
terminal AUX IN.
*
3
Equipo opcional auxiliar como un
reproductor de DVD portátil (no
suministrado)
suministrado)
*
4
Suministrado con el equipo auxiliar
*
5
Suministrado con el XA-C40
*
6
Insertar con el cable hacia arriba.
*
5
*
4
*
3
ɠ To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
system may damage the unit.
ɡ To the interface cable of a car telephone
ɢ To a car’s illumination signal
Be sure to connect the black ground lead to a metal surface
of the car fi rst.
of the car fi rst.
ɣ To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground lead to a metal
surface of the car fi rst.
• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply
leads.”
leads.”
ɤ To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to a metal surface
of the car fi rst.
of the car fi rst.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V DC
• The power antenna control lead (blue) supplies +12 V DC
when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/side
glass, connect the power antenna control lead (blue) or the
accessory power input lead (red) to the power terminal of the
existing antenna booster. For details, consult your dealer.
accessory power input lead (red) to the power terminal of the
existing antenna booster. For details, consult your dealer.
• A power antenna without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
left speaker.
• Do not connect the ground lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
If speaker and amplifi er are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
Connection example
Notes (
ǵ-A)
• Be sure to connect the ground lead before connecting the
amplifi er.
• The alarm will only sound if the built-in amplifi er is used.
Tip (
ǵ-B- )
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
selector XA-C40 (not supplied) is necessary.
Connection diagram
ɞ To a metal surface of the car
First connect the black ground lead, then connect the
orange/white striped, yellow, and red power input leads.
orange/white striped, yellow, and red power input leads.
ɟ To the power antenna control lead or power
supply lead of antenna booster amplifi er
Notes
• It is not necessary to connect this lead if there is no power
• It is not necessary to connect this lead if there is no power
antenna or antenna booster, or with a manually-operated
telescopic antenna.
telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply
leads.”
leads.”
Click on the first or last page to see other MEX-BT5100 service manuals if exist.