Read Sony MDX-CA790X Service Manual online
39
MDX-CA790X
•
MAIN BOARD IC600 MN101E01KDA1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
DAVDD
—
Power supply terminal (+3.3V)
2
NCO
O
Not used
3
DAVSS
—
Ground terminal
4 to 9
NCO
O
Not used
10
VDD1
—
Power supply terminal (+3.3V)
11
MMOD
I
Internal flash memory data write mode detection signal input terminal Not used
12
OSCOUT
O
System clock output terminal (27.648 MHz)
13
OSCIN
I
System clock input terminal (27.648 MHz)
14
VSS1
—
Ground terminal
15
XIN
I
System clock input terminal (32.768 kHz)
16
XOUT
O
System clock output terminal (32.768 kHz)
17
VDD2
—
Power supply terminal (+3.3V)
18
MOD1
I
Setting terminal for the CPU operational mode fixed at “H”
19
RESET
I
System reset signal input from the reset signal generator and reset switch “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
20
RCIN1
I
Rotary remote commander shift key input terminal
21
ACCIN
I
Accessory power detection signal input terminal “L”: accessory power on
22
TESTIN
I
Test mode setting terminal “L”: test mode, normally fixed at “H”
23
TELLATT
I
Telephone muting detection signal input terminal
At input of “H”, the audio signal is attenuated by 20 dB
At input of “H”, the audio signal is attenuated by 20 dB
24
ATT
O
Audio muting on/off control signal output terminal
25
ADON
O
A/D converter power control signal output
When the KEY ACK (pin 27) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
When the KEY ACK (pin 27) that controls reference voltage power for key A/D conversion input
is active, “L” is output from this terminal to enable the input
26
NCO
—
Not used
27
KEYACK
I
Acknowledge signal (wake up signal) input terminal for the key entry Acknowledge signal is
input to accept any function key in the standby status On at input of “H”
input to accept any function key in the standby status On at input of “H”
28
TUATTIN
I
Tuner muting zero-cross detection signal input terminal
29
MDON
I
Power supply on/off control signal input of the servo section
30
MDMON
I
Power supply on/off control signal input of the MD mechanism deck section
31
BUIN
I
Back up power supply detection signal input terminal “L” is input at low voltage
32
NCO
O
Not used
33
UNISO
O
Serial data output to the SONY bus interface IC
34
UNISI
I
Serial data input from the SONY bus interface IC
35
UNICKO
O
Serial data transfer clock signal output to the SONY bus interface IC and MD mechanism
controller
controller
36 to 38
NCO
O
Not used
39
OPENREQ
O
Front panel open request signal output terminal Not used
40
BUSON
O
SONY bus on/off control signal output terminal “L”: bus on
41
MDBOOT
O
Internal flash memory data write control signal output terminal Not used
42
SYSRST
O
System reset signal output to the MD mechanism controller and SONY bus interface IC
43 to 50
NCO
O
Not used
51
AMPATT
O
Amplifier muting on/off control signal output terminal Not used
52
DEST1
I
Setting terminal for the destination
53, 54
DEST2, DEST3
I
Setting terminal for model discrimination Not used
55
DOORSW
I
Front panel open/close detection input terminal “L”: close
Click on the first or last page to see other MDX-CA790X service manuals if exist.