Read Sony MDX-CA680 / MDX-CA680X Service Manual online
2
MDX-CA680/CA680X
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED
LINE WITH MARK
0
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
Never look into the laser diode emission from right avove when
checking it for adustment. It is feared that you will lose your sight.
checking it for adustment. It is feared that you will lose your sight.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
(KMS-241C).
(KMS-241C).
The laser diode in the optical pick-up block may suffer electro-
static break-down easily. When handling it, perform soldering
bridge to the laser-tap on the flexible board. Also perform mea-
sures against electrostatic break-down sufficiently before the op-
eration. The flexible board is easily damaged and should be
handled with care.
static break-down easily. When handling it, perform soldering
bridge to the laser-tap on the flexible board. Also perform mea-
sures against electrostatic break-down sufficiently before the op-
eration. The flexible board is easily damaged and should be
handled with care.
laser-tap
OPTICAL PICK-UP FLEXIBLE BOARD
1.
GENERAL
Location of Controls .......................................................
3
Setting the Clock .............................................................
4
2.
DISASSEMBLY
2-1. Disassembly Flow ........................................................... 10
2-2. Sub Panel Assy ................................................................ 10
2-3. Mechanism Deck (MG-164MA-138) ............................. 11
2-4. MAIN Board ................................................................... 11
2-5. Heat Sink ......................................................................... 12
2-6. SERVO Board ................................................................. 12
2-7. MD Cover Assy ............................................................... 13
2-8. Float Block ...................................................................... 13
2-9. Lo Motor Assy (Loading) (M903) .................................. 14
2-10. Lever (LE23) Assy .......................................................... 14
2-11. Holder Assy ..................................................................... 15
2-12. Chucking Arm Assy ........................................................ 15
2-13. Optical Pick-up (KMS-241C) ......................................... 16
2-14. SL Motor Assy (Sled) (M902),
2-2. Sub Panel Assy ................................................................ 10
2-3. Mechanism Deck (MG-164MA-138) ............................. 11
2-4. MAIN Board ................................................................... 11
2-5. Heat Sink ......................................................................... 12
2-6. SERVO Board ................................................................. 12
2-7. MD Cover Assy ............................................................... 13
2-8. Float Block ...................................................................... 13
2-9. Lo Motor Assy (Loading) (M903) .................................. 14
2-10. Lever (LE23) Assy .......................................................... 14
2-11. Holder Assy ..................................................................... 15
2-12. Chucking Arm Assy ........................................................ 15
2-13. Optical Pick-up (KMS-241C) ......................................... 16
2-14. SL Motor Assy (Sled) (M902),
SP Motor Assy (Spindle) (M901) ................................... 16
3.
ELECTRICAL ADJUSTMENTS
Test Mode ........................................................................ 17
MD Section ..................................................................... 17
Tuner Section .................................................................. 17
MD Section ..................................................................... 17
Tuner Section .................................................................. 17
4.
DIAGRAMS
................................................................. 18
4-1. Block Diagram – SERVO Section – ............................... 23
4-2. Block Diagram – TUNER Section – .............................. 24
4-3. Block Diagram – MAIN Section – ................................. 25
4-4. Block Diagram – BUS CONTROL/
4-2. Block Diagram – TUNER Section – .............................. 24
4-3. Block Diagram – MAIN Section – ................................. 25
4-4. Block Diagram – BUS CONTROL/
POWER SUPPLY Section – ........................................... 26
4-5. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 27
4-6. Printed Wiring Boards – SERVO Section – ................... 29
4-7. Schematic Diagram – SERVO Section (1/2) – ............... 30
4-8. Schematic Diagram – SERVO Section (2/2) – ............... 31
4-9. Printed Wiring Board – MAIN Board – ......................... 32
4-10. Schematic Diagram – MAIN Board (1/3) – ................... 33
4-11. Schematic Diagram – MAIN Board (2/3) – ................... 34
4-12. Schematic Diagram – MAIN Board (3/3) – ................... 35
4-13. Printed Wiring Board – SUB Board – ............................ 36
4-14. Schematic Diagram – SUB Board – ............................... 37
4-15. Printed Wiring Board – KEY Board – ............................ 38
4-16. Schematic Diagram – KEY Board – .............................. 39
4-17. IC Pin Function Description ........................................... 41
4-7. Schematic Diagram – SERVO Section (1/2) – ............... 30
4-8. Schematic Diagram – SERVO Section (2/2) – ............... 31
4-9. Printed Wiring Board – MAIN Board – ......................... 32
4-10. Schematic Diagram – MAIN Board (1/3) – ................... 33
4-11. Schematic Diagram – MAIN Board (2/3) – ................... 34
4-12. Schematic Diagram – MAIN Board (3/3) – ................... 35
4-13. Printed Wiring Board – SUB Board – ............................ 36
4-14. Schematic Diagram – SUB Board – ............................... 37
4-15. Printed Wiring Board – KEY Board – ............................ 38
4-16. Schematic Diagram – KEY Board – .............................. 39
4-17. IC Pin Function Description ........................................... 41
5.
EXPLODED VIEWS
5-1. General Section ............................................................... 49
5-2. Front Panel Section ......................................................... 50
5-3. Mechanism Deck Section-1 (MG-164MA-138) ............ 51
5-4. Mechanism Deck Section-2 (MG-164MA-138) ............ 52
5-2. Front Panel Section ......................................................... 50
5-3. Mechanism Deck Section-1 (MG-164MA-138) ............ 51
5-4. Mechanism Deck Section-2 (MG-164MA-138) ............ 52
6.
ELECTRICAL PARTS LIST
............................... 53
TABLE OF CONTENTS
Click on the first or last page to see other MDX-CA680 / MDX-CA680X service manuals if exist.