Read Sony DSX-MS60 Service Manual online
DSX-MS60
DSX-MS60
12
12
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• W : Indicates side identifi ed with part number.
• f : Internal component.
•
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• W : Indicates side identifi ed with part number.
• f : Internal component.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Indication of transistor.
C
B
These are omitted.
E
Q
• A : B+ Line.
• Power voltages is dc 14.4V and fed with regulated dc
• Power voltages is dc 14.4V and fed with regulated dc
power supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER
• Voltages are taken with a VOM (Input impedance 10 M
• Voltages are taken with a VOM (Input impedance 10 M
Ω).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
F
: AUDIO
f
: TUNER
l : USB
E
E
: AUX IN
j
: BUS AUDIO IN
• Waveforms
– MAIN Board –
2
IC501 od (OSC_OUT)
1 V/DIV, 50 ns/DIV
126 ns
3.8 Vp-p
3
IC204 ud (X2)
1 V/DIV, 50 ns/DIV
111 ns
3.4 Vp-p
1
IC501 qd (X_OUT)
1 V/DIV, 10
Ps/DIV
30.5
Ps
1.8 Vp-p
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
• All capacitors are in μF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in
Ω and
1
/
4
W or less unless otherwise
specifi ed.
• f : Internal component.
• C : Panel designation.
• C : Panel designation.
Note: When the MAIN board or IC502 on the MAIN board
are replaced, spread the compound referring to “NOTE
FOR WHEN REPLACING THE COMPLETE MAIN
BOARD OR IC502” on servicing notes (page 3).
FOR WHEN REPLACING THE COMPLETE MAIN
BOARD OR IC502” on servicing notes (page 3).
Note: When the MAIN board or IC502 on the MAIN board
are replaced, spread the compound referring to “NOTE
FOR WHEN REPLACING THE COMPLETE MAIN
BOARD OR IC502” on servicing notes (page 3).
FOR WHEN REPLACING THE COMPLETE MAIN
BOARD OR IC502” on servicing notes (page 3).
Click on the first or last page to see other DSX-MS60 service manuals if exist.