Read Sony DSX-A200UI / DSX-A202UI Service Manual online
DSX-A200UI/A202UI
3
SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
AUS :
AUS :
Australian
model
RU
: Russian model
NOTE OF REPLACING THE COMPLETE MAIN BOARD
OR SYSTEM CONTROLLER (IC501)
When the complete MAIN board or system controller (IC501) is
replaced, the destination setting is necessary.
OR SYSTEM CONTROLLER (IC501)
When the complete MAIN board or system controller (IC501) is
replaced, the destination setting is necessary.
1. Destination
Setting
Set destination according to the procedure below.
1-1. Setting the Destination Code
1. In the state of source off (the clock is displayed), enter the test
1. In the state of source off (the clock is displayed), enter the test
mode by pressing the buttons in order of the [
4]
t [5] t
[PAUSE 6] (press only the [PAUSE 6] button for two seconds).
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Clock display
2. In the state in which the system controller version is displayed
on the liquid crystal display (refer to following fi gure), enter
the destination setting mode by pressing the buttons in order of
the [
the destination setting mode by pressing the buttons in order of
the [
>
M
SEEK+]
t [SEEK–
m
.
]
t [PUSH ENTER/
MENU].
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
System controller version
3. Input the alphanumeric character of 12 digits of “F XXXXXX”
displayed on the liquid crystal display, and execute the destina-
tion setting.
tion setting.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Note: Refer to following “1-3. Entering the Destination Code” on page 4
for operation method.
Destination code
12 digits
OP0
OP1
OP2
OP3
OP4
OP5
4. The resetting operation is executed by pressing the [ OFF
SRC] button for 1 second after the setting ends, and the unit
returns to the normal condition.
returns to the normal condition.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Display after reset
– Continued on next page –
Click on the first or last page to see other DSX-A200UI / DSX-A202UI service manuals if exist.