Read Sony DSX-A100U / DSX-A102U Service Manual online
DSX-A100U/A102U
14
SECTION 4
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
•
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
For Schematic Diagrams.
Note:
• All capacitors are in
• All capacitors are in
μF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in
and
1
/
4
W or less unless otherwise
specifi ed.
• C : panel designation.
• A : B+ Line.
• Power voltages is dc 14.4V and fed with regulated dc
• Power voltages is dc 14.4V and fed with regulated dc
power supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM)
( ) : TUNER (AM)
( ) : TUNER (AM)
*
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F :
F :
AUDIO
f :
TUNER
d :
USB
E :
AUX
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Indication of transistor.
C
B
These are omitted.
E
Q
Note: When the complete MAIN board is replaced, the
destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 3.
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 3.
Note: When the complete MAIN board is replaced, the
destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 3.
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 3.
• Waveforms
– MAIN Board –
2
IC501 7 (XT2)
1 V/DIV, 10
Ps/DIV
30.4
Ps
2.1 Vp-p
3
IC501 0 (CF2)
1 V/DIV, 50 ns/DIV
108 ns
2.8 Vp-p
4
IC1301 1 (LX)
5 V/DIV, 1
Ps/DIV
2.4
Ps
15.2 Vp-p
1
IC601 ug (XOUT)
1 V/DIV, 50 ns/DIV
83 ns
2.6 Vp-p
Click on the first or last page to see other DSX-A100U / DSX-A102U service manuals if exist.