Read Sony CDX-V60 Service Manual online
– 3 –
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
The laser diode in the optical pick-up block may suffer electro-
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Laser Diode Properites
• Material: GaAlAs
• Wavelength: 780 nm
• Emission Duration: continuous
• Laser Output Power: less than 44.6 µW*
• Wavelength: 780 nm
• Emission Duration: continuous
• Laser Output Power: less than 44.6 µW*
* This output is the value measured at a distance of 200 mm
from the objective lens surface on the Optical Pick-up Block.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-
UP BLOCK OR BASE UNIT
UP BLOCK OR BASE UNIT
OPERATING METHOD OF THIS SET
The key controller of this set makes control via serial communica-
tion with the master unit (car audio set compatible with the SONY
bus system such as a CD changer controller).
Therefore, in repairing this set, connect as shown below.
tion with the master unit (car audio set compatible with the SONY
bus system such as a CD changer controller).
Therefore, in repairing this set, connect as shown below.
UNLOADING METHOD OF MAGAZINE AT POWER OFF
Remove the side panels (L)/(R), front panel ass’y, and case
(upper). (See SECTION 3. DISASSEMBLY on page 7.)
(upper). (See SECTION 3. DISASSEMBLY on page 7.)
1. Push the arm (M lock) ass’y toward the arrow A.
2. Draw out the magazine ass’y toward the arrow B.
2. Draw out the magazine ass’y toward the arrow B.
Note:
This is possible only when the trays are all stored in the magazine.
If a disc or tray is left protrudent, the magazine must be ejected by
turning on the power.
If a disc or tray is left protrudent, the magazine must be ejected by
turning on the power.
arm (M lock) ass’y
magazine ass’y
A
B
monitor TV
set
master unit
VIDEO
OUT jack
BUS CONTROL
OUT connector
BUS CONTROL IN connector
parking brake terminal
(connect to ground)
(connect to ground)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
Click on the first or last page to see other CDX-V60 service manuals if exist.