Read Sony CDX-T70MXDC Service Manual online
34
CDX-T70MXDC/MP3 CDC 6
Pin No.
Pin Name
I/O
Description
55, 56
MD0, MD1
I
Setting terminal for the CPU operational mode "H": single chip mode (fixed at "H" in this set)
57
OSC2
O
Sub system clock output terminal Not used
58
OSC1
I
Sub system clock input terminal Not used (fixed at "L")
59
RES
I
System reset signal input from the SONY bus interface and reset signal generator "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H"
60
NMI
O
Not used (fixed at "H")
61
STBY
O
Standby mode control signal output terminal Not used (fixed at "H")
62
VCC
-
Power supply terminal (+3.3V)
63
XTAL
I
Main system clock input terminal (12.288 MHz)
64
VSS
-
Ground terminal
65
EXTAL
O
Main system clock output terminal (12.288 MHz)
66
FWE
I
Flash memory data write enable signal input terminal
67
MD2
I
Setting terminal for the CPU operational mode "H": single chip mode (fixed at "H" in this set)
68
FL BOOT
I
Flash memory data write control signal input terminal "L" active
69
FL W
O
Flash memory data write control signal output (connecting FWE (pin 66))
70, 71
NC
O
Not used
72
MGLK-SW
I
Magazine in/out detect switch input terminal "L": magazine in
73
DECINT
I
Interrupt signal input from the CD-ROM/MP3 decoder
74
NC
O
Not used
75
EJECT
I
Eject switch input terminal "L" active
76
SO
O
Serial data output to the SONY bus interface
77
SI
I
Serial data input from the SONY bus interface
78
SCLK
I
Serial data transfer clock signal input from the SONY bus interface
79
EEDATA
I/O
Two-way data bus with the EEPROM
80
SDA
I/O
I2C interface data input/output with the CD-ROM/MP3 decoder
81
SCL
O
I2C interface data transfer clock signal output to the CD-ROM/MP3 decoder
82
EECLK
O
Serial data transfer clock signal output to the EEPROM
83
NC
O
Not used
84
SQSO
I
Subcode Q data input from the DSP
85
SQCK
O
Subcode Q data reading clock signal output to the DSP
86 to 89
NC
O
Not used
90
R/RW SEL
O
CD-ROM/RW selection signal output "L": CD-RW, "H": CD-ROM
91
BUSON
I
Bus on/off control signal input from the SONY bus interface "L": bus on
92
BUCHK
I
Battery detection signal input "H": low battery (Normally: "L")
93, 94
NC
O
Not used
95
LOADF
O
Motor drive signal (load chucking direction) output to the chucking motor drive
96
LOADR
O
Motor drive signal (save direction) output to the chucking motor drive
97
SINGLE
I
Setting terminal for the single disc/multiple discs mode
"L": single disc mode, "H": multiple discs mode (fixed at "H" in this set)
"L": single disc mode, "H": multiple discs mode (fixed at "H" in this set)
98
LOAD SW
I
Chucking end detect switch input terminal
"L": When completion of the disc chucking, loading or save operation
"L": When completion of the disc chucking, loading or save operation
99
SAVE SW
I
Chucking end detect switch input terminal
"L": When completion of the disc chucking, loading or save operation
"L": When completion of the disc chucking, loading or save operation
100
LIM SW
I
Sled limit in detect switch input terminal
"L": When the optical pick-up is inner position
"L": When the optical pick-up is inner position
Click on the first or last page to see other CDX-T70MXDC service manuals if exist.