Read Sony CDX-GT700D / CDX-GT705DX Service Manual online
22
22
CDX-GT700D/GT705DX
CDX-GT700D/GT705DX
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in Ω and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
For printed wiring boards.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
a
: Through hole.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
• B : B– Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• CD mechanism section (1/2), (2/2)
no mark : CD PLAY
• Main (1/4), (2/4), (3/4), (4/4) and Display sections
no mark : FM/MW/LW
no mark : CD PLAY
• Main (1/4), (2/4), (3/4), (4/4) and Display sections
no mark : FM/MW/LW
<
> : CD PLAY
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J
: CD PLAY
F
: FM
f
: MW/LW
L
: BUS AUDIO
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)
Pattern face side: Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side:
Parts on the parts face side seen from the
(Side A)
parts face are indicated.
Q
C
These are omitted
E
B
E
These are omitted
C
B
C
These are omitted
B
E
• Waveforms
— SERVO Board —
(CD PLAY)
— MAIN Board —
4-4. CIRCUIT BOARDS LOCATION
MAIN board
SUB board
SENSOR board
SERVO board
DISPLAY board
tuner unit
(TU1)
(TU1)
1
IC2 5 (FEI)
Approx.
1Vp-p
1Vp-p
0 V
0.6 Vp-p
16.9344 MHz
Approx. 100 mVp-p
50 mV/DIV, 5 msec/DIV
0.5 V/DIV, 0.5
µ
sec/DIV
2
IC2 6 (TEI)
200 mV/DIV, 5 msec/DIV
6
IC2 oh (FPI2), oj (FPI1)
0.5 V/DIV, 0.5
µ
sec/DIV
Approx. 400 mVp-p
3
IC2 wd (XI)
0.2 V/DIV, 0.2
µ
sec/DIV
7
IC3 ia (X1)
0.5 V/DIV, 0.2
µ
sec/DIV
1.1 Vp-p
12 MHz
4
IC2 ia (RFI)
0.5 V/DIV, 0.5
µ
sec/DIV
5
IC2 of (FNI2), og (FNI1)
1.5 Vp-p
1.5 Vp-p
0 V
1
IC901 qa (XOUT)
3.0 Vp-p
1 V/div, 50 nsec/div
6.747 kHz
— DISPLAY Board —
11 Vp-p
6
IC620 4 (OUT)
5 V/div, 1
µ
sec/div
2.97
µ
sec
3.2 Vp-p
10 Vp-p
11.2896 MHz
3
IC650 4 (OUT)
4
IC303 9 (XCOUT)
5 V/div, 1
µ
sec/div
2
IC801 ed (MCLKI)
1 V/div, 50 nsec/div
2.7 Vp-p
1 V/div, 10
µ
sec/div
32.768 kHz
2.1 Vp-p
8.664 MHz
1
IC551 0 (XT0)
1 V/DIV, 50 nsec/DIV
3.6 Vp-p
6 MHz
5
IC303 qa (XOUT)
1 V/DIV, 50 nsec/DIV
3
µ
sec
• Abbreviation
CND : Canadian model.
Note:
The components
identified by mark 0 or
dotted line with mark 0
are critical for safety.
Replace only with part
number specified.
The components
identified by mark 0 or
dotted line with mark 0
are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Click on the first or last page to see other CDX-GT700D / CDX-GT705DX service manuals if exist.