Read Sony CDX-GT355 Service Manual online
6
CDX-GT355
L
R
BUS AUDIO IN
AUDIO OUT
FRONT
AUDIO OUT
REAR
*
2
BUS
CONTROL IN
REMOTE
IN
2
4
5
6
7
1
3
AUDIO
OUT
REAR
AUDIO
OUT
FRONT
BUS
AUDIO
IN
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched SUB or
REAR. For details, see the Operating
Instructions.
Instructions.
*
3
Insert with the cord upwards.
2
AMP REM
Max. supply current 0.3 A
Fuse (10 A)
Blue/white striped
Red
Yellow
White
Green
Purple
White/black striped
Grey/black striped
Green/black striped
Grey
Left
Right
Left
Right
ANT REM
Black
Blue
Max. supply current 0.1 A
Purple/black striped
*
1
Source selector
(not supplied)
XA-C40
Supplied with the CD/MD changer
*
1
ATT
ILLUMINATION
Orange/white striped
Light blue
*
3
Supplied with XA-C40
from car aerial
Connection diagram
1
To a metal surface of the car
First connect the black earth lead, then connect the orange/
white stripped, yellow, and red power input leads.
white stripped, yellow, and red power input leads.
2
To the power aerial control lead or power
supply lead of aerial booster amplifi er
Notes
• It is not necessary to connect this lead if there is no power
• It is not necessary to connect this lead if there is no power
aerial or aerial booster, or with a manually-operated
telescopic aerial.
telescopic aerial.
• When your car has a built-in FM/MW/SW aerial in the rear/
side glass, see “Notes on the control and power supply
leads.”
leads.”
3
To AMP REMOTE IN of an optional power
amplifi er
This connection is only for amplifi ers. Connecting any other
system may damage the unit.
system may damage the unit.
4
To the interface cable of a car telephone
5
To a car’s illumination signal
Be sure to connect the black earth lead to a metal surface
of the car fi rst.
of the car fi rst.
6
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black earth lead to a metal surface
of the car fi rst.
• When your car has a built-in FM/MW/SW aerial in the rear/
side glass, see “Notes on the control and power supply
leads.”
leads.”
7
To the +12 V power terminal which is
energized at all times
Be sure to connect the black earth lead to a metal surface
of the car fi rst.
of the car fi rst.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V DC when
• The power aerial control lead (blue) supplies +12 V DC when
you turn on the tuner.
• When your car has built-in FM/MW/SW aerial in the rear/side
glass, connect the power aerial control lead (blue) or the
accessory power input lead (red) to the power terminal of the
existing aerial booster. For details, consult your dealer.
accessory power input lead (red) to the power terminal of the
existing aerial booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
left speaker.
• Do not connect the earth lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
• Connect only passive speakers. Connecting active speakers
(with built-in amplifi ers) to the speaker terminals may damage
the unit.
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
If speaker and amplifi er are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifi er are connected correctly.
Click on the first or last page to see other CDX-GT355 service manuals if exist.