Read Sony CDX-G1170U / CDX-G3170UV Service Manual online
CDX-G1170U/G3170UV
CDX-G1170U/G3170UV
13
13
4-2. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section -
REGULATOR
IC201
1
9
TU5V
VCC1
8
CTRL1
6
CTRL2
CN301 (2/2)
7
VCC2
15
EXT
BU
15
9
AMP_REM
3 CD_6V
13 SW3.3V
13
ACC
SYSTEM CONTROLLER
IC501 (2/2)
J801
(REMOTE IN)
81 RC_IN1
72 RE_IN1
73 RE_IN0
73 RE_IN0
90 NOSE_SW
64 SIRCS
78 KEYIN1
79 KEYIN0
79 KEYIN0
80 RC_IN0
48 LCD_SO
46 LCD_CLK
47 LCD_CE
46 LCD_CLK
47 LCD_CE
62
5
RESET
63
KEY_ACK0
KEY_ACK1
KEY BOARD (2/2)
LCD_DATA
LCD_CLK
LCD_CE
SIRCS
KEY_1
KEY_0
KEY_0
RE_1
RE_0
RE_0
PANEL_SW
11 V6IN
AUDIO_3.3V
12 VDD_3.3V
P-COM_3.3V
USB_VBUS
DRV_6V
TU_5V
33
CTRL2_C
17
EN_USB
25
SYNC_OUT
30
CTRL1_C
31
CTRL2_A
5 ILM_9V
FP_B+
ACC_IN 51
BU_IN 35
VCC
18
FLT
D351
D350
BATTERY
CHECK
Q301
ACCESSORY
CHECK
Q304
BACK UP
VOLTAGE DETECT
Q300, 302
D500
DC/DC
CONVERTER
IC1301
VBUS SWITCH
IC1304 (G3170UV)
IC1305 (G1170U)
D305
D200
D503
82
MECHA_ON
For Schematic Diagrams.
Note:
• All capacitors are in
• All capacitors are in
μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
tantalums.
• All resistors are in
Ω and 1/4 W or less unless otherwise
specifi ed.
• f : Internal component.
• C : Panel designation.
• C : Panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
• A : B+ Line.
• Power voltages is dc 14.4V and fed with regulated dc
• Power voltages is dc 14.4V and fed with regulated dc
power supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM)
( ) : CD PLAY
( ) : CD PLAY
*
: Impossible to measure
• Voltages are taken with VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F :
F :
AUDIO
f :
TUNER
J :
CD
E :
AUX
d :
USB
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• f : Internal component.
•
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• f : Internal component.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
• Indication of transistor.
C
B
These are omitted.
E
Q
Note: When the complete MAIN board is replaced, the
destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 4.
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 4.
Note: When the complete MAIN board is replaced, the
destination setting is necessary. Refer to “NOTE OF
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 4.
REPLACING THE COMPLETE MAIN BOARD OR
SYSTEM CONTROLLER (IC501)” on page 4.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note: The components identifi ed by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specifi ed.
Click on the first or last page to see other CDX-G1170U / CDX-G3170UV service manuals if exist.