Read Sony CDX-C680 / CDX-C780 (serv.man3) Service Manual online
– 1 –
SERVICE MANUAL
US Model
CDX-C680/C780
SUPPLEMENT-1
File this supplement with the service manual.
Subject : Change of Key, Main, Relay and Servo Boards
When performing service and inspection, check the suffix of the part number of
the key, main, relay and servo boards.
the key, main, relay and servo boards.
(ECN-CS800990)
- KEY BOARD - (SIDE B)
- RELAY BOARD - (SIDE A)
- MAIN BOARD - (SIDE A)
- SERVO BOARD - (SIDE A)
Key board Part No.
Former : 1-669-502-11
New : 1-669-502-12
Former : 1-669-502-11
New : 1-669-502-12
Main board Part No.
Former : 1-668-087-11
New : 1-668-087-12
Former : 1-668-087-11
New : 1-668-087-12
Servo board Part No.
Former : 1-664-298-13
New : 1-664-298-14
Former : 1-664-298-13
New : 1-664-298-14
Relay board Part No.
Former : 1-668-088-11
New : 1-668-088-12
Former : 1-668-088-11
New : 1-668-088-12
– 2 –
1. IC PIN DESCRIPTION
• IC5 CXP84640-011Q (CD SYSTEM CONTROL)
• IC5 CXP84640-011Q (CD SYSTEM CONTROL)
Pin No.
Pin Name
I/O
Pin Description
1 – 5
NCO
—
Not used in this set.
6
FP OPEN
I
Front panel open detection input
7
FP CLOSE
O
Front panel close control output
8
LINKOFF
I
Bus interface link input (Not used in this set.)
9
DRV OE
O
Focus/tracking coil/sled motor control output
10
D SW
I
Down switch input (SW4)
11 – 13
NCO
—
Not used in this set.
14
LM EJ
O
Loading motor control output
15
LM LOD
O
Loading motor control output
16
EMPH O
O
De-emphasis ON/OFF control output
17
CDMON
O
CD mechanism deck power control output
18
CD ON
O
CD power control output
19
A MUT
O
System attenuate control output
20
LD ON
O
Lazer power ON/OFF control output
21
CD RST
O
CD system reset output
22 – 24
—
—
Not used in this set.
25
PH3
I
Not used in this set.
26
TSTIN0
I
Not used in this set.
27
TSTIN1
I
Not used in this set.
28
TST CLV
I
Not used in this set.
29
NCO
—
Not used in this set.
30
RESET
I
System reset input (“L” = Reset)
31
X IN
I
X’tal oscillator input of system clock. (10 MHz)
32
X OUT
O
X’tal oscillator output of system clock. (10 MHz)
33
GND
—
Analog GND
34
XT OUT
O
Not used in this set.
35
XT IN
I
Not used in this set.
36
AVSS
—
A/D converter GND
37
AVREF
I
A/D converter reference voltage input
38
TEP L
I
Not used in this set.
39
TEP H
I
Not used in this set.
40
NCO
—
Not used in this set.
41
PH2
I
Not used in this set.
42
SCLK
O
CD-TEXT data read clock output
43
ESPXQOK
O
XQOK signal output to DRAM controller.
44
ESPSDT
I
Serial data input from DRAM controller.
45
GRSRST
O
Reaet signal output to DRAM controller.
46
GRSCOR
I
Sub-cord sync input from DRAM controller.
47
CD XLAT
O
CD signal process serial latch output
48
TX CLK
O
EEPROM serial clock output
49
TX DATA
O
EEPROM serial data output
50
UNISO
O
Not used in this set.
51
BUS CLK
I/O
Bus system serial clock input/output
52
BUS SI
I
Bus system serial interface input
53
BUS SO
O
Bus system serial interface output
54
F OK
I
Focus OK signal input
55
GFS
I
GFS signal detection input
56
SCOR
O
Sub-cord sync output
57
SENS
I
SENS signal input
58
—
I
Fixed at “H” in this set.
59
CD CKO
O
CD signal process serial clock output
– 3 –
Pin No.
Pin Name
I/O
Pin Description
60
BU.IN
I
Back-up power detection input
61
BUSON
I
Bus on control input
62
IN SW
I
Disc in switch input (SW2)
63
SELF SW
I
Self switch input (SW2)
64
TX CE
O
EEPROM chip enable output
65
SCK2
O
Sub Q read clock output
66
SI2
I
Sub Q 80 bit, PCM peak and level data 16 bit input
67
CD DATA™
O
CD signal process serial data output
68
ESPXWRE
O
Write signal output to DRAM controller.
69
ESPXRDE
O
Read signal output to DRAM controller.
70
ESPXLT
O
Serial data latch output to DRAM controller.
71
ESPXSOE
O
XSOE signal output to DRAM controller.
72
VDD
—
Power supply
73
HIN
I
Fixed at “H” in this set.
74
TEXT.ON/OFF
I
Fixed at “H” in this set.
75
PH1
I
Not used in this set.
76
FBTBSEL
I
Not used in this set.
77
CDOSEL
I
Not used in this set.
78 – 80
—
—
Not used in this set.
– 11 –
CDX-C680/C780
• Waveforms
(MODE:PLAY)
1
2
3
4
5
6
7
Approx. 620mVp-p
IC1
!§
(FE)
0V
IC1
!¶
(RFO)
1.2Vp-p
Approx. 200mVp-p
IC1
!¢
(TE)
0V
IC501
&ª
(MDP)
2.6Vp-p
7.6
µ
sec
IC501
*¶
(LRCK)
5.8Vp-p
22.7
µ
sec
IC501
(¡
(BCK)
5.7Vp-p
474nsec
16.89MHz
IC501
`⁄‚‹
(XTAI)
3.2Vp-p
Note: The components identified by mark
!
or dotted line
with mark
!
are critical for safety.
Replace only with part number specified.
Note:
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF:
µµ
F
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
%
: indicates tolerance.
•
¢
: internal component.
•
U
: B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltage and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD PLAY
no mark : CD PLAY
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Signal path.
J
: CD