Read Sony TA-P9000ES Service Manual online
MICROFILM
SERVICE MANUAL
MULTICHANNEL PRE AMPLIFIER
US Model
Canadian Model
AEP Model
TA-P9000ES
SPECIFICATIONS
Photo: gold type
– 2 –
TABLE OF CONTENTS
1.
SERVICING NOTES
...............................................
3
2.
GENERAL
...................................................................
4
3.
DISASSEMBLY
.........................................................
5
4.
DIAGRAMS
4-1. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
7
4-2. Printed Wiring Boards
– MAIN Board/SUB VOLUME Board/
MASTER VOLUME Board – ...................................
MASTER VOLUME Board – ...................................
9
4-3. Schematic Diagram
– MAIN Board (1/2)/SUB VOLUME Board/
MASTER VOLUME Board – ................................... 11
MASTER VOLUME Board – ................................... 11
4-4. Schematic Diagram – MAIN Board (2/2) – .................. 13
4-5. Printed Wiring Boards – PANEL Section – .................. 15
4-6. Schematic Diagram – PANEL Section – ....................... 17
4-7. Printed Wiring Boards – POWER Section – ................. 19
4-8. Schematic Diagram – POWER Section – ..................... 21
4-9. IC Pin Function Description ........................................... 23
4-5. Printed Wiring Boards – PANEL Section – .................. 15
4-6. Schematic Diagram – PANEL Section – ....................... 17
4-7. Printed Wiring Boards – POWER Section – ................. 19
4-8. Schematic Diagram – POWER Section – ..................... 21
4-9. IC Pin Function Description ........................................... 23
5.
EXPLODED VIEWS
................................................ 24
6.
ELECTRICAL PARTS LIST
............................... 27
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
!
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COM-
POSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
– 3 –
SECTION 1
SERVICING NOTES
MODEL IDENTIFICATION
– Specification Label –
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15
µ
F
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
MODEL NO.
TA-P9000ES
MULTI CHANNEL PRE AMPLIFIER
SERIAL NO.
MADE IN JAPAN
MADE IN JAPAN
US, Canadian models : AC 120V 60Hz 20W
AEP model : AC 220 - 230V 50/60Hz 20W
– 4 –
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.