TA-FA1200ES - Sony Audio Service Manual (repair manual). Page 14

14

All preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of
repair.
Procedure:
1. While pressing the [DIRECT] and [MUTING] buttons, press the   [POWER] button to turn on the main power.
2. The message “MEMORY CLEARING...” appears and the memories are reset to the default values.
3. When done, the message “MEMORY CLEARED !” appears.

Items

Protector on/off

Model version display

Model/destination change

FM/AM tuner version display
HDMI controller version
display

HDMI controller update mode
Speaker output setting

FL display fonts test

FL display test

Audio swap mode

DSP halt

DSP Version display

Volume value display (FL/FR)

Volume value display (SL/SR)
Volume value display (CT/SW)

Procedure:
1. Press the [POWER] button to turn on the main power and the [SPEAKERS] switch is set in off, then while pressing the [DIRECT] button,

press the [MUTING] button.

2. The message “MENU SPECIALIZED!” appears.
3. When  

U  u  key of the remote commander is pressed after [MENU] key of the remote commander is pressed, the message “SPECIAL”

appers.

4. The item of special menu mode is selected pressing  

U  u  key of the remote commander after [ENTER] key of the remote commander

is pressed.

5. To release from this mode, the [SPEAKERS] switch is set in off and while pressing the [DIRECT] button, press the [MUTING] button

again, the message “MENU SPECIALIZED OFF” appears.

Turn on the power supply again when usually operating after it changes in special menu mode.

The setting remains even if coming off the menu. The setting is cleared when turning off power.

Display

PROTECTOR ON/OFF [XXX]

##### *** vX. XX @@@@

MODEL [##### * * * *] X X

FM/AM Tuner Ver X. XX

HDMI Micom Ver X. XX

HDMIUcom Update [XXX]

SPEAKER OUT XXXXX

FL FONT 0x** = [X]

ALL ON

SWAP [XXXXXXXXXXX]

DSP HALT [XXX]

DSP Ver S: ***, P: XXX

FL**** FR XXXX

SL**** SR XXXX
CT**** SW XXXX

Remark

“ON”: Power supply will cut in 5 seconds when the protector
works.

“OFF”: Power supply doesn't cut when the protector works.

It is not possible to set it to ON until turning off power when
the protector setting is set to OFF. Turn on the power supply
again when setting it to ON.

XXX: ON or OFF (It switches by pressing the  

U  u  key of the

remote commander after the item is fixed pressing the [ENTER] key
of the remote commander)

#####: model
***: destination
X.XX: main system controller software version
@@@@: Sum value of flash memory in the main system controller

Not used
Not used

Not used

Not used

XXXXX: Selection of speaker output audio
[SOURCE]: nomally mode, [MIC]: mode that output audio from
mic from speaker (It switches by pressing the  

U  u  key of the

remote commander after the item is fixed pressing the [ENTER] key of
the remote commander)
**: 20 to FE, X: character (It switches by pressing the  

U  u  key of

the remote commander after the item is fixed pressing the [ENTER]
key of the remote commander)

Each time DISPLAY button to change as follows.
all on 

→

 test pattern 1 

→

 test pattern 2 

→

 all off 

→

 all on

Not used

XXX: ON or OFF (It switches by pressing the  

U  u  key of the

remote commander after the item is fixed pressing the [ENTER] key
of the remote commander)
Mode not to send DSP host code, and to make only decipherment
done
***: DSP decoder patch version
XXX: DSP post process version

****: Front L-ch volume value
XXXX

: 

Front R-ch volume value

Not used

Not used