Read Sony STR-DN2010 Service Manual online
STR-DN2010
5
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SECTION 1
SERVICING NOTES
NOTE OF REPLACING THE IC3500 AND IC3501 ON
THE D-VIDEO BOARD
IC3500 and IC3501 on the D-VIDEO board cannot exchange with
single. When these parts on the D-VIDEO board are damaged, ex-
change the entire mounted board.
THE D-VIDEO BOARD
IC3500 and IC3501 on the D-VIDEO board cannot exchange with
single. When these parts on the D-VIDEO board are damaged, ex-
change the entire mounted board.
NOTE OF REPLACING THE IC8001 AND IC8013 ON
THE NETWORK HUB BOARD
IC8001 and IC8013 on the NETWORK HUB board cannot ex-
change with single. When these parts on the NETWORK HUB
board are damaged, exchange the entire mounted board.
THE NETWORK HUB BOARD
IC8001 and IC8013 on the NETWORK HUB board cannot ex-
change with single. When these parts on the NETWORK HUB
board are damaged, exchange the entire mounted board.
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
PROTECTOR
Irregular current is output to the speakers, or
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
Error messages
For other messages, see “Message list after
Auto Calibration measurement”, “DIGITAL
MEDIA PORT message list” and “Satellite
radio message list”.
Auto Calibration measurement”, “DIGITAL
MEDIA PORT message list” and “Satellite
radio message list”.
Initializing the receiver
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their initial settings.
Be sure to use the buttons on the receiver for
this operation.
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their initial settings.
Be sure to use the buttons on the receiver for
this operation.
1
Press
?/1 to turn off the
receiver.
2
Hold down MUTING and MUSIC,
then press
then press
?/1 to turn on the
receiver.
3
Release MUTING and MUSIC
after a few seconds.
after a few seconds.
After “CLEARING” appears on the
display for a while, “CLEARED!”
appears.
All the settings you have changed or
adjusted are reset to the initial settings.
display for a while, “CLEARED!”
appears.
All the settings you have changed or
adjusted are reset to the initial settings.
Note
It takes about 30 seconds for the memory to be
cleared completely. Do not turn the receiver off until
“CLEARED!” appears on the display.
cleared completely. Do not turn the receiver off until
“CLEARED!” appears on the display.
?/1
MUSIC
MUTING
Resetting sound fields to
the initial settings
the initial settings
Be sure to use the buttons on the receiver for
this operation.
this operation.
1
Press
?/1 to turn off the
receiver.
2
While holding down MUSIC,
press
press
?/1.
“S.F. CLEAR” appears on the display and
all sound fields are reset to their initial
setting.
all sound fields are reset to their initial
setting.
?/1
MUSIC
Reference sections for clearing
the receiver’s memory
the receiver’s memory
Click on the first or last page to see other STR-DN2010 service manuals if exist.