Read Sony STR-DN1000 Service Manual online
STR-DN1000
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTE OF REPLACING THE IC2022 ON THE DIGITAL
BOARD
IC2022 on the DIGITAL board cannot exchange with single.
When this part on the DIGITAL board is damaged, exchange the
entire mounted board.
BOARD
IC2022 on the DIGITAL board cannot exchange with single.
When this part on the DIGITAL board is damaged, exchange the
entire mounted board.
NOTE OF REPLACING THE IC3203, IC3506 AND
IC3508 ON THE DIGITAL VIDEO BOARD
IC3203, IC3506 and IC3508 on the DIGITAL VIDEO board can-
not exchange with single. When these parts on the DIGITAL VID-
EO board are damaged, exchange the entire mounted board.
IC3508 ON THE DIGITAL VIDEO BOARD
IC3203, IC3506 and IC3508 on the DIGITAL VIDEO board can-
not exchange with single. When these parts on the DIGITAL VID-
EO board are damaged, exchange the entire mounted board.
NOTE OF REPLACING THE IC5021 ON THE DSP
BOARD
IC5021 on the DSP board cannot exchange with single. When this
part on the DSP board is damaged, exchange the entire mounted
board.
BOARD
IC5021 on the DSP board cannot exchange with single. When this
part on the DSP board is damaged, exchange the entire mounted
board.
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
PROTECTOR
Irregular current is output to the speakers, or
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
For other messages, refer to “Operating
instructions”.
instructions”.
If you are unable to remedy the problem,
clearing the receiver’s memory may remedy
the problem. However, note that all memorized
settings will be reset to their initial settings and
you will have to readjust all settings on the
receiver.
clearing the receiver’s memory may remedy
the problem. However, note that all memorized
settings will be reset to their initial settings and
you will have to readjust all settings on the
receiver.
Error messages
Reference sections for clearing
the receiver’s memory
the receiver’s memory
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
Be sure to use the buttons on the receiver for
this operation.
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
Be sure to use the buttons on the receiver for
this operation.
1
Press
?/1 to turn off the
receiver.
2
Hold down
?/1 for 5 seconds.
After “CLEARING” appears on the
display for a while, “CLEARED!”
appears.
All the settings you have changed or
adjusted are reset to the initial settings.
display for a while, “CLEARED!”
appears.
All the settings you have changed or
adjusted are reset to the initial settings.
Performing initial setup
operations
operations
MULTI CHANNEL DECODING
?/1
INPUT SELECTOR
MUTING
MASTER VOLUME
?/1
Resetting sound fields to
the initial settings
the initial settings
Be sure to use the buttons on the receiver for
this operation.
this operation.
1
Press
?/1 to turn off the
receiver.
2
While holding down MUSIC,
press
press
?/1.
“S.F. CLEAR” appears on the display and
all sound fields are reset to their initial
setting.
all sound fields are reset to their initial
setting.
?/1
MASTER VOLUME
SPEAKERS
PHONES
2 CH/
A.DIRECT
A.F.D.
MOVIE
MUSIC
INPUT MODE
DIMMER
DISPLAY
VIDEO 2 IN
VIDEO
L AUDIO R
AUTO CAL MIC
MULTI CHANNEL DECODING
INPUT SELECTOR
MUTING
?/1
MUSIC
Click on the first or last page to see other STR-DN1000 service manuals if exist.