Read Sony STR-DG900 Service Manual online
3
STR-DG900
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
MODEL IDENTIFICATION
— BACK PANEL —
Part No.
MODEL
PART No.
CND
2-666-932-9s
• Abbreviation
CND : Canadian model
ASSIGNABLE
(INPUT ONLY)
DVD
IN
COAXIAL
SA-CD/
CD
IN
OPTICAL
VIDEO 1
IN
TV/SAT
IN
MD/
TAPE
IN
MD/
TAPE
OUT
SIGNAL GND
DIGITAL
XM
ANTENNA
AM
TV/SAT
AUDIO IN
VIDEO IN
S-VIDEO
IN
DVD
AUDIO IN
VIDEO IN
S-VIDEO
IN
R
L
AUDIO
VIDEO
V
PHONO
IN
SA-CD/CD
L
R
L
R
MULTI CH IN
OUT
IN
L
R
FRONT
SURROUND
L
R
SURR
BACK
BACK
IN
MD/TAPE
ASSIGNABLE
IN 1
IN 2
MONITOR
OUT
HDMI
CN5003
JIG (J-2501-299-A)
NOTE OF HANDLING THE HDMI RE BOARD (Part
No. A-1193-890-A)
No. A-1193-890-A)
When the HDMI RE board is replaced by a repair for a fee, throw
away the HDMI RE board after obtaining consent of not returning
of the HDMI RE board to the customer. When throwing away the
HDMI RE board, be sure to throw away after destroying IC5004
and IC5005 physically with the hammer etc.
away the HDMI RE board after obtaining consent of not returning
of the HDMI RE board to the customer. When throwing away the
HDMI RE board, be sure to throw away after destroying IC5004
and IC5005 physically with the hammer etc.
UPDATE OF SOFTWARE OF THE HDMI
CONTROLLER (IC5006)
CONTROLLER (IC5006)
Connect:
Procedure:
1. Connect CN5003 on the HDMI RE Board with Jig (part no.: J-
1. Connect CN5003 on the HDMI RE Board with Jig (part no.: J-
2501-299-A) by using FFC. Connect Jig Board with PC by
using RS232 cross cable.
using RS232 cross cable.
2. Set the SW5002 of Jig Board HIGH side.
3. Activate SPECIAL MENU MODE by pressing ?/1 button to
3. Activate SPECIAL MENU MODE by pressing ?/1 button to
turn on the main power while holding [TUNING MODE] and
[INPUT MODE] button. The message “SPECIALIZED” appears.
[INPUT MODE] button. The message “SPECIALIZED” appears.
4. Use [TONE +/--] knob to select HDMI UPDATE OFF in
SPECIAL menu. Change “HDMI UPDATE OFF” to “HDMI
UPDATE ON” by using [TUNING +/--] knob.
UPDATE ON” by using [TUNING +/--] knob.
5. Push reset switch (SW5001) of the jig.
6. Boot the “FlashSta.exe” of update application distributed with
6. Boot the “FlashSta.exe” of update application distributed with
the manual.
7. Select “Baud rate=19200” and “Program_intervals=40”.
8. Select “Select Program=Internal flash memory” and
8. Select “Select Program=Internal flash memory” and
“RS232C=using com port”.
9. Click “Refer” and select mot file. Set “ID=FF FF FF FF FF FF
FF”.
10. Select “MCU Type=M16C/20 62”.
11. Click “E.P.R” to start update software.
12. To check the HDMI controller software version, use
11. Click “E.P.R” to start update software.
12. To check the HDMI controller software version, use
[TONE +/--] knob to select HDMI VER X.XX in SPECIAL menu.
Click on the first or last page to see other STR-DG900 service manuals if exist.