Read Sony STR-DA5200ES Service Manual online
5
STR-DA5200ES
COLOR VARIATION
Destination
COLOR
BLACK
SILVER
US, Canadian
z
AEP, UK
z
z
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE THE IC3601 ON THE HDMI BOARD AND
IC084 ON THE USB BOARD REPLACING
IC084 ON THE USB BOARD REPLACING
Replacement of IC3601 on the HDMI board and IC084 on the USB
board used in this set requires a special tool.
board used in this set requires a special tool.
•
MODEL IDENTIFICATION
Model
PART No.
US and Canadian models
2-668-097-7[]
AEP model
2-668-097-8[]
UK model
2-668-097-9[]
PART No.
– Back Panel –
NOTE OF REPLACING THE IC3509 AND IC3513 ON
THE HDMI BOARD
THE HDMI BOARD
When IC3509 and IC3513 on the HDMI board are damaged,
exchange the new HDMI board for the HDMI board which IC
damaged. When throwing away the HDMI board, be sure to throw
away after destroying IC3509 and IC3513 physically with the
hammer etc.
exchange the new HDMI board for the HDMI board which IC
damaged. When throwing away the HDMI board, be sure to throw
away after destroying IC3509 and IC3513 physically with the
hammer etc.
UPDATE OF SOFTWARE OF THE SYSTEM CONTROLLER (IC2054)/HDMI CONTROLLER (IC3610)/
USB CONTROLLER (IC006)
USB CONTROLLER (IC006)
Perform operation of the following when the update of software of the system controller (IC2054)/HDMI controller (IC3610)/USB controller
(IC006) is necessary.
(IC006) is necessary.
Connect:
Procedure:
1. Turn off the main power and setting the jig referring to Fig. 1 (Note: Do this setting before connecting jig with the set).
2. Remove the KNOB (VOL) ASSY and connect CN713 (M-VOLA3 board) and PC by using the jig.
3. Turn on the main power and perform the operation according to the application.
4. After “Please Reset” is displayed, reset switch on the jig is pushed and update is completed.
5. Turn off the main power and remove the jig.
6. Turn on the main power.
2. Remove the KNOB (VOL) ASSY and connect CN713 (M-VOLA3 board) and PC by using the jig.
3. Turn on the main power and perform the operation according to the application.
4. After “Please Reset” is displayed, reset switch on the jig is pushed and update is completed.
5. Turn off the main power and remove the jig.
6. Turn on the main power.
JIG
(Part No. : J-2501-300-A)
(Part No. : J-2501-300-A)
for PC
CN713
M-VOLA3 board
SW2 SW1
(RESET)
SW1: up, SW2: down
When system controller (IC2054) is updated
Fig.1 Setting for jig
SW2 SW1
(RESET)
SW1: up, SW2: up
When HDMI controller (IC3610) is updated
SW2 SW1
SW1: down, SW2: up
When USB controller (IC006) is updated
(RESET)
Click on the first or last page to see other STR-DA5200ES service manuals if exist.