Read Sony STR-DA4300ES Service Manual online
21
STR-DA4300ES
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT],
[MUSIC], [MOVIE] button in order, the message “MENU SPECIALIZED!” appears.
2. Press the
M
m
button of the remote commander, the message “<<< SPECIAL >>>” appears.
3. Press the
,
button of the remote commander, the item is appears.
4. Each time the
M
m
button of the remote commander is pressed, the item is switched in order as follows.
Some items can change the content. Display the cursor by pressing the
,
button of the remote commander, and changing the content
by pressing the
M
m
button of the remote commander, and fix the content by pressing the
<
button of the remote commander when you
want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in
order again, the message “MENU SPECIALIZED OFF” appears.
Items
Display
Remark
Video factory menu
<VIDEO FACTORY MENU>
Menu mode to enter video calibration menu and DDR access check menu
If the [ENTER] button of the remote commander is pressed, entering the
menu, and operating two the following menu become possible
Video calibration
V.CALIBRATION START?
Procedure:
(Video factory menu)
1. “DVD” is selected by using [INPUT SELECTOR] jog.
2. Connect a color pattern generator to the COMPONENT VIDEO DVD/
BD IN jack (J6001) and DVD/BD VIDEO IN jack (J6004) on the
A_VIDEO board.
3. Input 100% color bars signal from the color pattern generator.
4. Menu that measures individual difference of hardness by automatic
operation in pressing the [ENTER] button of the remote commander, and
corrects reference value.
In a measurement once, only one of NTSC/PAL/HD can be measured
”Check XXXX V-IN” at display:
Video signal necessary for the measurement while measuring it last time
was not detected and it became an error
Confirm the input of the video of the terminal connection etc. , and
measure the [ENTER] button of the remote commander again pressing
DDR access check
DDR CHECK [XX] sec
XX: Time to do access check on DDR (for design evaluation)
(Video factory menu)
Auto cal mic test
SPEAKER OUT [XXXXX]
XXXXX: Selection of speaker output audio
[SOURCE]: normally mode, [MIC]: mode that output audio from mic from
speaker
FL display fonts test
FL FONT [0x ** = X]
**: 20 to FE, X: character
FL display test
ALL ON
Each time DISPLAY button to change as follows
all on
t test pattern 1 t test pattern 2 t all off t all on
HDCP key read
HDCP KEY READ [XXX]
XXX: ON or OFF
DSP SRAM check
<DSP SRAM CHECK>
XX: OK or NG
r
[ENTER] button of the remote
OK: success access SRAM, NG: fail access to SRAM
commander
SRAM1 [XX] SRAM2 [XX]
Model version display
##### *** vX. XX @@@@
#####: Model
***: Destination
X.XX: System controller software version
@@@@: Sum value of flash memory in the system controller
Video Ucom version display
Video Ucom Ver X. XX
X.XX: Video system controller software version
FAROUDJA version display
FAROUDJA Ver X. XX
X.XX: Video Processor software version
DSP Ucom version display
DSP Ucom Ver X. XX
X.XX: DSP controller version
DSP serial flash version display
DSP SFLASH Ver X. XX
X.XX: Serial flash software version
DSP parallel flash version display
DSP PFLASH Ver X. XX
X.XX: DSP parallel flash version
DSP Version display
DSP Ver S: ***, P: XXX
***: DSP decoder patch version, XXX: DSP post process version
DSP halt
DSP HALT [XXX]
XXX: ON or OFF
DSP RAM
[*****]=XXXXXXXX
Mode that refers to internal RAM of DSP (for design evaluation)
Click on the first or last page to see other STR-DA4300ES service manuals if exist.