STR-DA3600ES - Sony Audio Service Manual (repair manual). Page 17

SOFTWARE  VERSION  DISPLAY  MODE
The software version is displayed.

Note: In this mode, never press the [

M] and [m] buttons on the remote 

commander.

Procedure:
1.  While pressing the [TONE MODE] and [MUSIC] buttons, 

press the [

?/1

] button to turn on the main power.

2.  The message “MAIN vX. XX” appears.
 

Each time the [DISPLAY] button is pressed, “SUB CCvX. 
XX”, “VIDEO vX. XX”, “FARO1 vX. XX”, “FARO2 vX. 
XX”, “LM vX. XX” “NET XCvX. XX”, “SFLASH X.XX” 
and “SYS. vX. XXX” this order, and returns to the “MAIN vX. 
XX” displayed.

SHIPMENT  MODE
Initialize backup of EEPROM and Network and return to state of 
the shipment.
Procedure:
1.  While pressing the [TONE MODE] and [MOVIE/HD-D.C.S.] 

buttons, press the [

?/1

] button to turn on the main power.

2.  The message “CLEARING*” appears and return to state of the 

shipment.

3.  When done, the message “STANDBY” appears and turn off 

the main power.

REBOX  TEST  MODE
Displayed the number of times of the power on after the shipment.
Procedure:
1.  While pressing the [A.F.D.] and [SPEAKERS A/B/A+B/OFF] 

buttons, press the [

?/1

] button to turn on the main power.

2.  The message “REBOX- XX” appears.

KEY  CHECK  MODE
Button check
Procedure:
1.  While pressing the [MEMORY/ENTER] and the [MOVIE/

HD-D.C.S.] buttons, press the [

?/1

] button to turn on the main 

power.

2.  Either the message “REST 11” appears.
 

Every pressing of any button other than the [

?/1

] counts down 

the buttons. The buttons which are already counted once are 
not counted again. When all buttons are pressed “REST 00” 
appears.

DMPORT  TEST  MODE
Procedure:
1.  Connect the DMPORT check jig (Part No. J-2501-309-A) with 

the DMPORT jack (CN2111) on the MICOM board.

2.  While pressing the [MEMORY/ENTER] and [A.F.D.] buttons, 

press the [

?/1

] button to turn on the main power.

3.  The message “DMPORT OK”appears on the fl uorescent indi-

cator tube and enter the DMPORT test mode (Confi rmation of 
communication line).

 

When “NO DETECT”, “UART NG” and “UART TO” are dis-
played on the fl uorescent indicator tube, confi rm the connec-
tion of the DMPORT check jig, and enter the mode again.

 

Each time the [

>] button on the remote commander is 

pressed, the connect check and adaptor version check are 
switched.

 

Press the [

.] button on the remote commander, connected 

confi rmation of the DMPORT check jig is done again.

4.  To a pin-jack of the DMPORT check jig input information 

relevant to audio signal (sine-wave 1.0 Vrms) and composite 
video signal (white 100% 1.0 Vp-p, color bar, etc.).

5. Confi rm the output of speakers and monitor TV (Confi rmation 

of analog signal).

6.  To release from this mode, press the [

x] button on the remote 

commander. 

SIRIUS  FACTORY  TEST  MODE
(US and Canadian models)
Mode to confi rm operation of SIRIUS. Doing display of ID of 
SIRIUS antenna and output of audio signal that SIRIUS antenna 
generates, it is confi rmed that there are no problems in the commu-
nication of the SIRIUS antenna and the transmission of the audio 
signal.
Procedure:
1.  The SIRIUS antenna was connected, while pressing the 
 

[TUNING MODE] and [A.F.D.] buttons, press the [

?/1

] but-

ton to turn on the main power.

2.  Whenever the [DISPLAY] button is pressed, the Module ver-

sion, SSP version, Security processor version, Audio processor 
version, Firmware product ID, Firmware product sequence ID, 
Sirius ID are displayed, next the output of the audio signal of 
1 kHz L/R, 20 Hz L/R, 10 Hz L/R, noise L, noise R and stop 
tone are switched.