Read Sony STR-DA3300ES / STR-DG1100 Service Manual online
SERVICE MANUAL
AUDIO POWER
SPECIFICATIONS
SPECIFICATIONS
(US model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
HARMONIC DISTORTION:
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
PO
DA3300ES: US and Canadian models/
DG1100:
DA3300ES: US and Canadian models/
DG1100:
WER OUTPUT
Rated Power Output at Stereo Mode
1) 2)
(8 ohms 20 Hz – 20 kHz,
THD 0.09%):
100 W + 100 W
THD 0.09%):
100 W + 100 W
Reference Power Output at Stereo Mode
(4 ohms 20 Hz – 20 kHz,
THD 0.15%):
85 W + 85 W
THD 0.15%):
85 W + 85 W
Reference Power Output
(8 ohms 1 kHz, THD 0.7%)
FRONT
FRONT
2)
:
110 W + 110 W
CENTER
CENTER
2)
: 110 W
SURROUND
2)
:
110 W + 110 W
SUR BACK
SUR BACK
2)
:
110 W + 110 W
Reference Power Output
(4 ohms 1 kHz, THD 0.7%)
FRONT
FRONT
2)
:
100 W + 100 W
CENTER
CENTER
2)
: 100 W
SURROUND
2)
:
100 W + 100 W
SUR BACK
SUR BACK
2)
:
100 W + 100 W
1)
Depending on the sound field settings and the
source, there may be no sound output.
source, there may be no sound output.
2)
Measured under the following conditions:
Power requirements: 120 V AC, 60 Hz
Power requirements: 120 V AC, 60 Hz
Frequency response
PHONO
RIAA equalization curve
± 0.5 dB
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV
VIDEO 1/2/3
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV
VIDEO 1/2/3
10 Hz – 100 kHz
± 3 dB
Rated Po
DA3300ES: AEP, Russian, Ukrainian and
UK models:
wer Output at Stereo Mode
1) 2)
(8 ohms 1 kHz, THD
0.7%):
105 W + 105 W
0.7%):
105 W + 105 W
Reference Power Output at Stereo Mode
2)
(4 ohms 1 kHz, THD
0.7%):
105 W + 105 W
0.7%):
105 W + 105 W
Reference Power Output
(8 ohms 20 Hz – 20 kHz,
THD 0.09%)
FRONT
THD 0.09%)
FRONT
2)
:
100 W + 100 W
CENTER
CENTER
2)
:
100 W
SURROUND
SURROUND
2)
:
100 W + 100 W
SURROUND BACK
SURROUND BACK
2)
:
100 W + 100 W
Reference Power Output
(4 ohms 20 Hz – 20 kHz,
THD 0.7%)
FRONT
THD 0.7%)
FRONT
2)
:
100 W + 100 W
CENTER
CENTER
2)
:
100 W
SURROUND
SURROUND
2)
:
100 W + 100 W
SURROUND BACK
SURROUND BACK
2)
:
100 W + 100 W
Reference Power Output at Stereo Mode
(8 ohms 1 kHz, THD
10%):
130 W + 130 W
10%):
130 W + 130 W
Reference Power Output at Stereo Mode
(4 ohms 1 kHz, THD
10%):
130 W + 130 W
10%):
130 W + 130 W
MULTI CHANNEL AV RECEIVER
SPECIFICATIONS
STR-DA3300ES/DG1100
Ver. 1.5 2010.02
– Continued on next page –
9-887-742-06
2010B05-1
© 2010.02
© 2010.02
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
US Model
STR-DA3300ES/DG1100
Canadian Model
AEP Model
UK Model
STR-DA3300ES
This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System.
*
*
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories.
Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories.
** Manufactured under license from DTS, Inc.
“DTS”, “DTS-ES” and “Neo:6” are registered trademarks of DTS, Inc. “DTS 96/24” is a trademark of DTS, Inc.
Photo: STR-DA3300ES
2
STR-DA3300ES/DG1100
AM tuner section
Tuning range
With 10-kHz tuning scale
530 – 1,710 kHz
3)
With 9-kHz tuning scale
531 – 1,710 kHz
3)
Antenna (aerial)
Loop antenna (aerial)
3)
You can change the AM tuning scale to either 9
kHz or 10 kHz. After tuning in any AM station,
turn off the receiver. While holding down
TUNING MODE, press POWER on the receiver.
All preset stations will be erased when you change
the tuning scale. To reset the scale to 10 kHz (or 9
kHz), repeat the procedure.
kHz or 10 kHz. After tuning in any AM station,
turn off the receiver. While holding down
TUNING MODE, press POWER on the receiver.
All preset stations will be erased when you change
the tuning scale. To reset the scale to 10 kHz (or 9
kHz), repeat the procedure.
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
HDMI Video
Input/Output (HDMI Repeater block)
640
× 480p@60 Hz
720
× [email protected]/60 Hz
1440
× [email protected]/60 Hz (pixel sent 2times)
1280
× [email protected]/60 Hz
1920
× [email protected]/60 Hz
1920
× [email protected]/60 Hz
720
× 576p@50 Hz
1440
× 576p@50 Hz (pixel sent 2times)
1280
× 720p@50 Hz
1920
× 1080i@50 Hz
1920
× 1080p@50 Hz
1920
× 1080p@24 Hz
Genera l
Po
DA3300ES: US and Canadian models/DG1100:
DA3300ES: US and Canadian models/DG1100:
wer requirements
Power output (DIGITAL MEDIA PORT)
DC OUT
120 V AC, 60 Hz
DA3300ES: AEP, Russian, Ukrainian and
UK models:
UK models:
230 V AC, 50/60 Hz
(in countries/area in
Europe other than the U.K.)
230 – 240 V AC, 50/60 Hz
(in the U.K. and general area)
(in countries/area in
Europe other than the U.K.)
230 – 240 V AC, 50/60 Hz
(in the U.K. and general area)
DA3300ES: US and Canadian models/DG1100:
350 W/480 VA (US/Canada)
DA3300ES: AEP, Russian, Ukrainian and
UK models:
UK models:
390 W
: 5 V, 700 mA
Power consumption
Power consumption (during standby mode)
0.7 W (when “HDMI
Control” and “RS-232C
Control” are set to “OFF”)
Control” and “RS-232C
Control” are set to “OFF”)
Dimensions
430
× 175 × 430 mm
(width/height/depth)
including projecting parts
and controls
including projecting parts
and controls
Mass (Approx.)
14.5 kg
Supplied accessories
Operating Instructions
Quick Setup Guide (1)
HDMI CONTROL Guide (1)
GUI Menu List (1)
Optimizer microphone ECM-AC2 (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
AC power cord (mains lead) (1) (DA3300ES)
Remote commander RM-AAL011 (1)
(DA3300ES: US and Canadian models)
Remote commander RM-AAP019 (1)
(DA3300ES: AEP, Russian, Ukrainian and UK models)
(DA3300ES)
Remote commander RM-AAU018 (1)
(DG1100)
Remote commander RM-AAP018 (1)
R6 (size-AA) batteries
(4 (DA3300ES) or 2 (DG1100))
(4 (DA3300ES) or 2 (DG1100))
Design and specifications are subject to
change without notice.
change without notice.
Inputs (Analog)
Inputs (Digital)
Outputs
PHONO
Sensitivity: 2.5 mV
Impedance: 50 kohms
S/N: 90 dB (A, 20 kHz
LPF)
Impedance: 50 kohms
S/N: 90 dB (A, 20 kHz
LPF)
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV,
VIDEO 1/2/3
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV,
VIDEO 1/2/3
Sensitivity: 150 mV
Impedance: 50 kohms
S/N: 100 dB (A, 20 kHz
LPF)
Impedance: 50 kohms
S/N: 100 dB (A, 20 kHz
LPF)
DVD/BD,VIDEO 2,
SA-CD/CD (Coaxial)
SA-CD/CD (Coaxial)
Impedance: 75 ohms
S/N: 96 dB (A, 20 kHz
LPF)
S/N: 96 dB (A, 20 kHz
LPF)
VIDEO 1, VIDEO 3,
SAT/CATV, TV,
MD/TAPE (Optical)
SAT/CATV, TV,
MD/TAPE (Optical)
S/N: 96 dB
(A, 20 kHz LPF)
(A, 20 kHz LPF)
MD/TAPE (REC OUT),
VIDEO 1 (AUDIO OUT)
VIDEO 1 (AUDIO OUT)
Voltage:150 mV
Impedance: 1 kohm
Impedance: 1 kohm
FRONT L/R, CENTER,
SURROUND L/R,
SUR BACK L/R, SUB
WOOFER
SURROUND L/R,
SUR BACK L/R, SUB
WOOFER
Voltage: 2 V
Impedance: 1 kohm
Impedance: 1 kohm
EQUALIZER
Gain levels
±10 dB, 1 dB step
FM tuner section
Tuning range
87.5 – 108.0 MHz
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Reference Power Output
(8 ohms 1 kHz, THD 10%)
FRONT
FRONT
2)
:
130 W + 130 W
CENTER
CENTER
2)
:
130 W
SURROUND
SURROUND
2)
:
130 W + 130 W
SURROUND BACK
SURROUND BACK
2)
:
130 W + 130 W
Reference Power Output
(4 ohms 1 kHz, THD 10%)
FRONT
FRONT
2)
:
130 W + 130 W
CENTER
CENTER
2)
:
130 W
SURROUND
SURROUND
2)
:
130 W + 130 W
SURROUND BACK
SURROUND BACK
2)
:
130 W + 130 W
1)
Depending on the sound field settings and the
source, there may be no sound output.
source, there may be no sound output.
2)
Measured under the following conditions:
Power requirements: 230 V AC, 50/60 Hz
Power requirements: 230 V AC, 50/60 Hz
(in countries/area in Europe
other than the U.K.)
240 V AC, 50/60 Hz
(in the U.K. and general
area)
other than the U.K.)
240 V AC, 50/60 Hz
(in the U.K. and general
area)
Frequency response
PHONO
RIAA equalization curve
± 0.5 dB
MULTI CHANNEL
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV,
VIDEO 1/2/3
INPUT, SA-CD/CD,
MD/TAPE, DVD/BD,
TV, SAT/CATV,
VIDEO 1/2/3
10 Hz – 100 kHz
± 3 dB
Tu
DA3300ES: AEP, Russian, Ukrainian and
UK models:
UK models:
DA3300ES: US and Canadian models/DG1100:
ning range
531 – 1,602 kHz
(With 9-kHz tuning scale)
(With 9-kHz tuning scale)
Antenna (aerial)
Loop antenna (aerial)
Ver. 1.2
3
STR-DA3300ES/DG1100
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15
µ
F
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
4
STR-DA3300ES/DG1100
TABLE OF CONTENTS
1.
SERVICING NOTES
..............................................
5
2.
GENERAL
.................................................................. 11
3.
DISASSEMBLY
3-1.
Disassembly Flow .......................................................... 16
3-2.
Case ................................................................................ 17
3-3.
Front Panel Block ........................................................... 17
3-4.
CIS Board (DA3300ES: US and Canadian models),
Tuner (FM/AM) .............................................................. 18
Tuner (FM/AM) .............................................................. 18
3-5.
D_AUDIO Board, DSP Board ........................................ 18
3-6.
TUNER Board, CONTROL Board ................................ 19
3-7.
PREOUT Board (DA3300ES), SUB WOOFER
Board (DG1100) and S_SPTM Board ............................ 19
Board (DG1100) and S_SPTM Board ............................ 19
3-8.
D_VIDEO Board ............................................................ 20
3-9.
A_VIDEO Board ............................................................ 20
3-10. MAIN Board, C_SPTM Board ....................................... 21
3-11. AC Board, Power Transformer (T001) ........................... 22
3-12. Power AMP Block .......................................................... 22
3-11. AC Board, Power Transformer (T001) ........................... 22
3-12. Power AMP Block .......................................................... 22
4.
TEST MODE
............................................................. 23
5.
ELECTRICAL ADJUSTMENTS
........................ 27
6.
DIAGRAMS
6-1.
Block Diagram – CONTROL Section – ......................... 28
6-2.
Block Diagram – DSP Section – .................................... 29
6-3.
Block Diagram – HDMI Section – ................................. 30
6-4.
Block Diagram – VIDEO PROCESS Section – ............. 31
6-5.
Block Diagram – ANALOG AUDIO Section – ............. 32
6-6.
Block Diagram – POWER AMP Section – .................... 33
6-7.
Block Diagram – VIDEO Section – ............................... 34
6-8.
Block Diagram – PANEL, CIS, XM/
SIRIUS RECEIVER, DMPORT Section – .................... 35
SIRIUS RECEIVER, DMPORT Section – .................... 35
6-9.
Block Diagram – POWER SUPPLY Section – .............. 36
6-10. Printed Wiring Board
– D_AUDIO Board (Component Side) – ....................... 38
6-11. Printed Wiring Board
– D_AUDIO Board (Conductor Side) – ......................... 39
6-12. Schematic Diagram – D_AUDIO Board (1/4) – ............ 40
6-13. Schematic Diagram – D_AUDIO Board (2/4) – ............ 41
6-14. Schematic Diagram – D_AUDIO Board (3/4) – ............ 42
6-15. Schematic Diagram – D_AUDIO Board (4/4) – ............ 43
6-16. Printed Wiring Board
6-13. Schematic Diagram – D_AUDIO Board (2/4) – ............ 41
6-14. Schematic Diagram – D_AUDIO Board (3/4) – ............ 42
6-15. Schematic Diagram – D_AUDIO Board (4/4) – ............ 43
6-16. Printed Wiring Board
– TUNER Board (Component Side) – ........................... 44
6-17. Printed Wiring Board
– TUNER Board (Conductor Side) – ............................. 45
6-18. Schematic Diagram – TUNER Board (1/2) – ................ 46
6-19. Schematic Diagram – TUNER Board (2/2) – ................ 47
6-20. Printed Wiring Board – DSP Board – ............................ 48
6-21. Schematic Diagram – DSP Board – ............................... 49
6-22. Printed Wiring Boards – CONNECTOR Section – ........ 50
6-23. Schematic Diagram – CONNECTOR Section – ............ 51
6-24. Printed Wiring Board
6-19. Schematic Diagram – TUNER Board (2/2) – ................ 47
6-20. Printed Wiring Board – DSP Board – ............................ 48
6-21. Schematic Diagram – DSP Board – ............................... 49
6-22. Printed Wiring Boards – CONNECTOR Section – ........ 50
6-23. Schematic Diagram – CONNECTOR Section – ............ 51
6-24. Printed Wiring Board
– TEMPERATURE DETECTION BOARD – ............... 52
6-25. Schematic Diagram
– TEMPERATURE DETECTION BOARD – ............... 52
6-26. Printed Wiring Board – A CLASS AMP Board – .......... 53
6-27. Schematic Diagram – A CLASS AMP Board (1/2) – .... 54
6-28. Schematic Diagram – A CLASS AMP Board (2/2) – .... 55
6-29. Printed Wiring Board – POWER AMP Board – ............ 56
6-30. Schematic Diagram – POWER AMP Board – ............... 57
6-31. Printed Wiring Board – PROTECTOR (F-C) Board – ... 58
6-32. Schematic Diagram – PROTECTOR (F-C) Board – ...... 59
6-33. Printed Wiring Boards
6-27. Schematic Diagram – A CLASS AMP Board (1/2) – .... 54
6-28. Schematic Diagram – A CLASS AMP Board (2/2) – .... 55
6-29. Printed Wiring Board – POWER AMP Board – ............ 56
6-30. Schematic Diagram – POWER AMP Board – ............... 57
6-31. Printed Wiring Board – PROTECTOR (F-C) Board – ... 58
6-32. Schematic Diagram – PROTECTOR (F-C) Board – ...... 59
6-33. Printed Wiring Boards
– PROTECTOR (SB/SURR) Section – .......................... 60
6-34. Schematic Diagram
– PROTECTOR (SB/SURR) Section – .......................... 61
6-35. Printed Wiring Board – BIAS Board – ........................... 62
6-36. Schematic Diagram – BIAS Board – ............................. 63
6-37. Printed Wiring Boards – SPEAKER Section – .............. 64
6-38. Schematic Diagram – SPEAKER Section – ................... 65
6-39. Printed Wiring Boards – PREOUT Section – ................ 66
6-40. Schematic Diagram – PREOUT Section – ..................... 67
6-41. Schematic Diagram – MAIN Board (1/4) – ................... 68
6-42. Schematic Diagram – MAIN Board (2/4) – .................... 69
6-43. Schematic Diagram – MAIN Board (3/4) – ................... 70
6-44. Schematic Diagram – MAIN Board (4/4) – ................... 71
6-45. Printed Wiring Board – MAIN Board – ......................... 72
6-46. Schematic Diagram – D_VIDEO Board (1/9) – ............ 73
6-47. Schematic Diagram – D_VIDEO Board (2/9) – ............ 74
6-48. Schematic Diagram – D_VIDEO Board (3/9) – ............ 75
6-49. Schematic Diagram – D_VIDEO Board (4/9) – ............ 76
6-50. Schematic Diagram – D_VIDEO Board (5/9) – ............ 77
6-51. Schematic Diagram – D_VIDEO Board (6/9) – ............ 78
6-52. Schematic Diagram – D_VIDEO Board (7/9) – ............ 79
6-53. Schematic Diagram – D_VIDEO Board (8/9) – ............ 80
6-54. Schematic Diagram – D_VIDEO Board (9/9) – ............ 81
6-55. Printed Wiring Board
6-36. Schematic Diagram – BIAS Board – ............................. 63
6-37. Printed Wiring Boards – SPEAKER Section – .............. 64
6-38. Schematic Diagram – SPEAKER Section – ................... 65
6-39. Printed Wiring Boards – PREOUT Section – ................ 66
6-40. Schematic Diagram – PREOUT Section – ..................... 67
6-41. Schematic Diagram – MAIN Board (1/4) – ................... 68
6-42. Schematic Diagram – MAIN Board (2/4) – .................... 69
6-43. Schematic Diagram – MAIN Board (3/4) – ................... 70
6-44. Schematic Diagram – MAIN Board (4/4) – ................... 71
6-45. Printed Wiring Board – MAIN Board – ......................... 72
6-46. Schematic Diagram – D_VIDEO Board (1/9) – ............ 73
6-47. Schematic Diagram – D_VIDEO Board (2/9) – ............ 74
6-48. Schematic Diagram – D_VIDEO Board (3/9) – ............ 75
6-49. Schematic Diagram – D_VIDEO Board (4/9) – ............ 76
6-50. Schematic Diagram – D_VIDEO Board (5/9) – ............ 77
6-51. Schematic Diagram – D_VIDEO Board (6/9) – ............ 78
6-52. Schematic Diagram – D_VIDEO Board (7/9) – ............ 79
6-53. Schematic Diagram – D_VIDEO Board (8/9) – ............ 80
6-54. Schematic Diagram – D_VIDEO Board (9/9) – ............ 81
6-55. Printed Wiring Board
– D_VIDEO Board (Component Side) – ....................... 82
6-56. Printed Wiring Board
– D_VIDEO Board (Conductor Side) – ......................... 83
6-57. Printed Wiring Board
– A_VIDEO Board (Component Side) – ........................ 84
6-58. Printed Wiring Board
– A_VIDEO Board (Conductor Side) – ......................... 85
6-59. Schematic Diagram – A_VIDEO Board (1/4) – ............. 86
6-60. Schematic Diagram – A_VIDEO Board (2/4) – ............. 87
6-61. Schematic Diagram – A_VIDEO Board (3/4) – ............. 88
6-62. Schematic Diagram – A_VIDEO Board (4/4) – ............. 89
6-63. Printed Wiring Board – VIDEO3 Board – ...................... 90
6-64. Schematic Diagram – VIDEO3 Board – ........................ 91
6-65. Printed Wiring Board
6-60. Schematic Diagram – A_VIDEO Board (2/4) – ............. 87
6-61. Schematic Diagram – A_VIDEO Board (3/4) – ............. 88
6-62. Schematic Diagram – A_VIDEO Board (4/4) – ............. 89
6-63. Printed Wiring Board – VIDEO3 Board – ...................... 90
6-64. Schematic Diagram – VIDEO3 Board – ........................ 91
6-65. Printed Wiring Board
– CONTROL Board (Component Side) – ...................... 92
6-66. Printed Wiring Board
– CONTROL Board (Conductor Side) – ........................ 93
6-67. Schematic Diagram – CONTROL Board (1/2) – ........... 94
6-68. Schematic Diagram – CONTROL Board (2/2) – ........... 95
6-69. Printed Wiring Board – CIS Board
6-68. Schematic Diagram – CONTROL Board (2/2) – ........... 95
6-69. Printed Wiring Board – CIS Board
(DA3300ES: US and Canadian models) – ..................... 96
Ver. 1.1