Read Sony STR-DA1500ES Service Manual online
STR-DA1500ES
2
Video section
Inputs/Outputs
Video:
Inputs/Outputs
Video:
1
Vp-p/75
ohms
General
Power requirements
Power requirements
Area code
Power requirements
US, CND
120 V AC, 60 Hz
AEP, UK
230 V AC, 50/60 Hz
Power output (DIGITAL MEDIA PORT)
DC OUT:
5 V, 0.7 A MAX
Power consumption
Area code
Power requirements
US, CND, AEP, UK
210W
Power consumption (during standby mode)
0.3 W (when “RS232C” is set to
“OFF”)
“OFF”)
Dimensions (w/h/d) (Approx.)
17 × 6 1/4 × 15 3/8 inches
(US, CND)
(430 × 157.5 × 388 mm)
including projecting parts and
controls
(US, CND)
(430 × 157.5 × 388 mm)
including projecting parts and
controls
Mass (Approx.)
19 lb 14 oz (9.0 kg) (US, CND)
9.2 kg (AEP, UK)
9.2 kg (AEP, UK)
Supplied accessories
Operating Instructions (this manual)
Quick Setup Guide (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
RM-AAU056 Remote Commander (1)
R6 (size-AA) batteries (2)
AC power cord (mains lead) (1)
Operating Instructions (this manual)
Quick Setup Guide (1)
FM wire antenna (aerial) (1)
AM loop antenna (aerial) (1)
RM-AAU056 Remote Commander (1)
R6 (size-AA) batteries (2)
AC power cord (mains lead) (1)
For details on the area code of the component you are using,
see page 3 (for AEP, UK) and page 4 (for US, CND)
see page 4.
see page 3 (for AEP, UK) and page 4 (for US, CND)
see page 4.
Design and specifi cations are subject to
change without notice.
change without notice.
Halogenated fl ame retardants are not used in the certain
printed wiring boards.
printed wiring boards.
• Abbreviation
CND : Canadian Model
CND : Canadian Model
UPDATE OF SOFTWARE OF IC600 ON THE MAIN
BOARD
Perform operation of the following when the update of software
of the IC600 on the MAIN board is necessary.
BOARD
Perform operation of the following when the update of software
of the IC600 on the MAIN board is necessary.
Connect:
AEP and UK models
AEP and UK models
For PC (J861)
US and Canadian models
For PC (J861)
Procedure:
1 Connect J861 on the CIS board and PC by using the
RS232C cable.
2 Set the service switch to the right.
3 Turn on the main power.
4 The update is executed by using PC.
5 When the update ends, turn off the main power.
6 Set the service switch to the left.
7 Remove the RS232C cable from the J861 on the CIS
board and PC.
1 Connect J861 on the CIS board and PC by using the
RS232C cable.
2 Set the service switch to the right.
3 Turn on the main power.
4 The update is executed by using PC.
5 When the update ends, turn off the main power.
6 Set the service switch to the left.
7 Remove the RS232C cable from the J861 on the CIS
board and PC.
Service Switch in Rear Panel
AEP and UK models
AEP and UK models
US and Canadian models
Used for maintenance and service.
Set to left for normal operation (initial setting).
Set to right for maintenance and service.
Set to right for maintenance and service.
Ver. 1.1
Service Switch
Service Switch
Click on the first or last page to see other STR-DA1500ES service manuals if exist.