Read Sony SS-SX7 Service Manual online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SS-SX7
SPECIFICATIONS
SPEAKER SYSTEM
9-896-164-02
2015G33-1
©
2015.07
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Ver. 1.1 2015.07
• SS-SX7 is Speaker system in CMT-SX7/SX7B.
Speaker system:
2-way speaker system, Bass Reflex
Woofer: 100 mm, cone type
Tweeter: 27 mm, Balanced soft dome type
Woofer: 100 mm, cone type
Tweeter: 27 mm, Balanced soft dome type
Rated impedance:
6 ohms
Dimensions (W/H/D):
Approx. 145 mm x 245 mm x 225 mm
Mass:
Approx. 3.5 kg (per unit)
Design and specifications are subject to
change without notice.
change without notice.
SS-SX7
2
SECTION 1
DISASSEMBLY
•
This set can be disassembled in the order shown below.
1-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
1-2. LOUDSPEAEKER (10 cm) (WOOFER) (SP1)
SET
1-2. LOUDSPEAEKER (10 cm)
(WOOFER)
(WOOFER)
(SP1)
(Page
2)
1-4. LOUDSPEAKER (19 mm)
(TWEETER)
(TWEETER)
(SP2)
(Page
4)
1-5. TERMINAL
(Page
(Page
4)
1-3. TWEETER
BLOCK
(Page
3)
Note: Please remove grille frame assy.
1 four hex. socket
screws
(3.5)
2 WF cover
5 loudspeaker (10 cm) (Woofer)
(SP1)
3 Pull out the loudspeaker
(10 cm) (Woofer) (SP1).
loudspeaker (10 cm)
(Woofer) (SP1)
(Woofer) (SP1)
terminal
(wide side)
(wide side)
terminal
(narrow side)
(narrow side)
terminal position
,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHU
FP:RRIHU63
FP:RRIHU63
–
5HDUYLHZ–
protrusion
protrusion
4 Push the protrusion,
and remove the
terminal (wide side).
4 Push the protrusion,
and remove the
terminal (narrow side).
SS-SX7
3
1-3. TWEETER BLOCK
2 two hex. socket
screws
(3.5)
1 two catch pins
4 All bosses are removed while
moving jig in the direction of
the arrow, and TW panel
block is removed.
4 All bosses are removed while
moving jig in the direction of
the arrow, and TW panel
block is removed.
3 Insert the jig into a space and raise
TW panel block.
Note: When using a jig, please work so
as not to injure TW panel block.
3 Insert the jig into a space and raise
TW panel block.
Note: When using a jig, please work so
as not to injure TW panel block.
total four bosses
5 Pull out the tweeter block.
7 tweeter block
terminal
(wide side)
(wide side)
terminal
(narrow side)
(narrow side)
– Rear view –
– Rear view –
protrusion
protrusion
6 Push the protrusion,
and remove the
terminal (narrow side).
6 Push the protrusion,
and remove the
terminal (wide side).
JIG
When disassembling the unit, use the following
jig for speaker removal.
jig for speaker removal.
Part No.
Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
SS-SX7
4
1-4. LOUDSPEAKER (19 mm) (TWEETER) (SP2)
1-5. TERMINAL
(TM1)
1 two tapping screws (1)
(3.5
u 14)
3 loudspeaker (19 mm)
(tweeter)
(SP2)
2 TW panel
– Inner view –
terminal
(wide side)
(wide side)
terminal
(narrow side)
(narrow side)
top side
2 Pull out the terminal block.
terminal
(wide side)
(wide side)
terminal
(narrow side)
(narrow side)
– Rear bottom view –
– Rear view –
protrusion
protrusion
3 Push the protrusion,
and remove the
terminal (wide side).
3 Push the protrusion,
and remove the
terminal (narrow side).
1 four screws
(B3
u 20)
4 terminal (TM1)
Ver. 1.1