Read Sony SS-HW5 Service Manual online
SERVICE MANUAL
Sony Video & Sound Products Inc.
Published by Sony Techno Create Corporation
SS-HW5
SPECIFICATIONS
SPEAKER SYSTEM
9-896-225-01
2015J33-1
©
2015.10
AEP Model
UK Model
Australian Model
Hong Kong Model
Singapore Model
Malaysia Model
Thai Model
Ver. 1.0 2015.10
• SS-HW5 is Speaker system in CAS-1.
Speaker system
2 way, 2 drivers speaker system, Bass reflex
Speakers unit
Tweeter: 14 mm, soft dome type × 1
Woofer: 62 mm, cone type × 1
Woofer: 62 mm, cone type × 1
Rated impedance
5 Ω
Dimensions (w/h/d) (including projecting parts and controls)
Approx. 95 mm × 178 mm × 172 mm
Mass
Approx. 1.5 kg
Design and specifications are subject to change without notice.
SS-HW5
2
SECTION 1
DISASSEMBLY
•
This set can be disassembled in the order shown below.
1-1. DISASSEMBLY FLOW
SET
1-2. RING (WF)
(Page
(Page
2)
1-3. 62 mm LOUDSPEAKER
(WOOFER)
(WOOFER)
(SP1)
(Page
3)
1-4. RING (TW)
(Page
(Page
4)
1-6. TERMINAL BOARD ASSY
(TB1)
(Page
(TB1)
(Page
5)
1-5. 14-20
mm TWEETER
(SP2)
(Page
(Page
4)
1-7. STABILIZER (S)
(Page
(Page
5)
Note: Follow the disassembly procedure in the numerical order given.
1-2. RING
(WF)
2 ring (WF)
Note
2: When removing the ring (WF), it is not re-used.
Be sure to replace it with new parts.
1 Insert a fingernail into the screw hole at lower
right 45 degrees from the inside of ring (WF),
and slowly remove the ring (WF).
Note 1: When using the screwdriver etc., cabinet
will
be
damaged.
ring (WF)
screw hole
cabinet
SS-HW5
3
1-3. 62 mm LOUDSPEAKER (WOOFER) (SP1)
1 four hex screws
(low head M3
u 12)
Note: WLJKWHQLQJWRUTXHNJFP
2 Pull out the 62 mm loudspeaker
(Woofer)
(SP1).
4 62 mm loudspeaker
(Woofer)
(SP1)
62 mm loudspeaker
(Woofer) (SP1)
(Woofer) (SP1)
terminal
(narrow side)
(narrow side)
terminal
(wide side)
(wide side)
terminal position
,QVWDOODWLRQGLUHFWLRQIRUWKHPPORXGVSHDNHU
:RRIHU63
:RRIHU63
protrusion
protrusion
3 Push the protrusion,
and remove the
terminal (wide side).
3 Push the protrusion,
and remove the
terminal (narrow side).
SS-HW5
4
1-4. RING
(TW)
1-5. 14-20 mm TWEETER (SP2)
2 ring (TW)
Note
2: When removing the ring (TW), it is not re-used.
Be sure to replace it with new parts.
ring (TW)
screw hole
cabinet
1 Insert a fingernail into the screw hole at top side
from the outside groove of the ring (TW), and
slowly remove the ring (TW).
Note 1: When using the screwdriver etc., cabinet
will
be
damaged.
1 three hex screws
(low head M3
u 12)
Note: WLJKWHQLQJWRUTXHNJFP
5 14-20 mm tweeter
(SP2)
4 tweeter plate
2 Pull out the 14-20 mm
tweeter (SP2) block.
,QVWDOODWLRQGLUHFWLRQIRUWKHPP
WZHHWHU63
WZHHWHU63
terminal position
14-20 mm tweeter
(SP2)
(SP2)
protrusion
3 Push the protrusion,
and remove the
terminal (wide side).
protrusion
3 Push the protrusion,
and remove the
terminal (narrow side).