Read Sony SS-GT5DB Service Manual online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SS-GT5DB
SPECIFICATIONS
SPEAKER SYSTEM
9-896-184-02
2015H33-1
©
2015.08
AEP Model
UK Model
E Model
Australian Model
Ver. 1.1 2015.08
• SS-GT5DB is Speaker system in MHC-GT5D.
• All of the units included in the MHC-GT5D (SS-
• All of the units included in the MHC-GT5D (SS-
GT5DB, SA-WGT5D, Remote control) are required
to confi rming operation of SS-GT5DB. Check in
advance that you have all of the units.
to confi rming operation of SS-GT5DB. Check in
advance that you have all of the units.
Speaker system:
2-way, bass reflex
Speaker unit (left):
Tweeter: 50 mm × 1, cone type
Midrange: 90 mm × 2, cone type
Midrange: 90 mm × 2, cone type
Speaker unit (right):
Tweeter: 50 mm × 1, cone type
Midrange: 90 mm × 2, cone type
Midrange: 90 mm × 2, cone type
Rated impedance:
4 ohms
Design and specifications are subject
to change without notice.
to change without notice.
SS-GT5DB
2
SECTION 1
DISASSEMBLY
•
This set can be disassembled in the order shown below.
1-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
1-2. FRONT PANEL BLOCK-1
•
Continued on 1-3 (page 3).
Note: L-ch and R-ch can be similarly disassembled.
The illustration of L-ch is used for explanation.
SET
1-2. FRONT PANEL BLOCK-1
(Page
(Page
2)
1-3. FRONT PANEL BLOCK-2
(Page
(Page
3)
1-4. TWEETER (47 mm) (SP3)
(Page
(Page
4)
1-5. MIDRANGE (82 mm) (SP1, SP2)
(Page
(Page
4)
JIG
When disassembling the unit, use the following
jig for speaker removal.
jig for speaker removal.
Part No.
Description
J-2501-238-A JIG FOR SPEAKER REMOVAL
1 three screws
(3.5
u 12)
3 two tapping screws
(1)
(3.5
u 14)
4 four tapping screws
(1)
(3.5
u 20)
5 bottom plate
6 bottom panel block
4 two tapping screws
(1)
(3.5
u 20)
2 top panel block
– Rear top view –
– Rear bottom view –
SS-GT5DB
3
1-3. FRONT PANEL BLOCK-2
7 front panel block
Note
3: When installing the front panel block,
remove the used bond and use a new
bond to fix the front panel block.
– Bottom view –
1 Insert a flat-head screwdriver into
the front panel block, and lift it a little.
1 Insert a flat-head screwdriver into
the front panel block, and lift it a little.
2 Insert the jig into a space and raise
front panel block.
Note
1: When using a jig, please work so
as not to injure front panel block
and speaker cabinet.
2 Insert the jig into a space and raise
front panel block.
Note
1: When using a jig, please work so
as not to injure front panel block
and speaker cabinet.
3 All bosses are removed while
moving jig in the direction of
the arrow, and front panel
block is removed.
3 All bosses are removed while
moving jig in the direction of
the arrow, and front panel
block is removed.
4 Remove the front panel block
in the direction of the arrow.
6 terminal [black]
(wide
side)
6 terminal [gray]
(narrow
side)
OK
NG
Note 2: When installing the speaker wire, make the
position of caulking of terminals is outside.
Caulking is outside.
Caulking is inside.
,QVtDOODtioQ GiUeFtioQ IoU tKe VSeDNeU wiUe
5 Push the protrusion, and remove
the
terminal.
protrusion
loudspeaker (47 mm)
(SP3) (tweeter)
(SP3) (tweeter)
Push
total ten bosses
Push
SS-GT5DB
4
1-4. TWEETER (47 mm) (SP3)
1-5. MIDRANGE (82 mm) (SP1, SP2)
1 two screws
(3.5
u 12)
front panel block
two bosses
hole
hole
– Rear bottom view –
2 loudspeaker (47 mm) (SP3) (tweeter)
Note: When installing the loudspeaker (47 mm) (SP3),
align the positions of the two bosses on the front
panel block with the two holes on the loudspeaker
(47 mm) (SP3).
1 four tapping screws
(1)
(3.5
u 14)
1 four tapping screws
(1)
(3.5
u 14)
2 Remove the loudspeaker (82 mm) (SP1)
block in the direction of the arrow.
2 Remove the loudspeaker
(82 mm) (SP2) block in
the direction of the arrow.
5 loudspeaker (82 mm) (SP2)
(midrange)
5 loudspeaker (82 mm) (SP1)
(midrange)
4 terminal [black]
(narrow
side)
4 terminal [black]
(narrow
side)
4 terminal [gray]
(wide
side)
4 terminal [gray]
(wide
side)
3 Push the protrusion, and remove
the
terminal.
Push
Push
Note: When installing the speaker wire, make the
position of caulking of terminals is outside.
OK
NG
Caulking is outside.
Caulking is inside.
,QVWDOODWLRQGLUHFWLRQIRUWKHVSHDNHUZLUH
protrusion
loudspeaker (82 mm) (midrange)
–7RSYLHZ–