Read Sony SS-CS3 Service Manual online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SS-CS3
SPECIFICATIONS
SPEAKER SYSTEM
9-893-940-01
2014B33-1
©
2014.02
US Model
Canadian Model
AEP Model
UK Model
Ver. 1.0 2014.02
• AEP and UK models are front speakers in SS-CS310CR.
Photo: The state which removed the front grille.
Speaker system
3-way 4-driver speaker
system, Bass reflex
system, Bass reflex
Speaker units
Woofer: 130 mm (5 1/4 in.),
cone type (2)
cone type (2)
Tweeter: 25 mm (1 in.), soft
dome type (1)
dome type (1)
Super tweeter: 19 mm (3/4
in.), soft dome type (1)
in.), soft dome type (1)
Rated impedance
6 Ω
Maximum input power
145 W
Sensitivity level
88 dB (2.83V, 1 m)
Frequency range
45 Hz - 50,000 Hz
Dimensions (width/height/depth)
Approx. 230 × 922 × 260 mm
(9 1/8 in. × 36 3/8 in. × 10 1/4
in.), including front grille
(9 1/8 in. × 36 3/8 in. × 10 1/4
in.), including front grille
Mass
Approx. 11.5 kg (25 lb. 5 oz.),
including front grille
including front grille
Supplied accessory
Foot pads (4) (US and Canadian models)
Design and specifications are subject to change
without notice.
without notice.
SS-CS3
2
SECTION 1
DISASSEMBLY
•
This set can be disassembled in the order shown below.
1-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
1-2. GRILLE
ASSY
SET
1-2. GRILLE
ASSY
(Page
2)
1-8. TERMINAL
ASSY
(TM1)
(Page
7)
1-3. FACE PLATE BLOCK
(Page
(Page
3)
1-7. LOUDSPEAKER (13 cm)
(WOOFER)
(WOOFER)
(SP1)
(Page
6)
1-4. SPEAKER (2.5 cm)
(TWEETER)
(TWEETER)
(SP3)
(Page
4)
1-5. SPEAKER (19 mm)
(SUPER TWEETER) (SP4)
(Page
4)
1-6. LOUDSPEAKER (13 cm)
(WOOFER)
(WOOFER)
(SP2)
(Page
5)
1 two bosses
1 boss
2 grille assy
1 boss
1 two bosses
• JIG
When disassembling the unit, use the following jig (for speaker
When disassembling the unit, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
SS-CS3
3
1-3. FACE PLATE BLOCK
:LUHVHWWLQJ
1 six screws
(3.5
(3.5
u 20)
3 terminal
[blue/black]
[blue/black]
3 terminal
[blue]
[blue]
2 Pull out the face plate block.
6 face plate block
5 terminal [gray/black]
4 cushion (STW)
5 terminal [gray]
Note: Cushion (STW) is not reused.
Be sure to exchange it for new parts.
4 cushion (STW)
Note: Cushion (STW) is not reused.
Be sure to exchange it for new parts.
face plate block
[black]
[gray/black]
[gray]
[gray]
[blue]
[blue/black]
–
5HDUYLHZ–
SS-CS3
4
1-4. SPEAKER (2.5 cm) (TWEETER) (SP3)
1-5. SPEAKER (19 cm) (SUPER TWEETER) (SP4)
– Face plate block rear view –
1 three screws
(BVTP3
(BVTP3
u 8)
2 speaker (2.5 cm) (tweeter)
(SP3)
1 two screws
(BVTP3
(BVTP3
u 8)
2 speaker (19 mm) (super tweeter)
(SP4)
– Face plate block rear view –