Read Sony SS-AR2 Service Manual online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
SS-AR2
SPECIFICATIONS
SPEAKERS SYSTEM
9-893-426-02
2012C33-1
©
2012.03
US Model
Ver. 1.1 2012.03
Speaker system
3-way 4-driver speaker system, Bass reflex
Speaker unit
Woofer: 165 mm (6.5 in), corn type (2)
Midrange: 130 mm (5.25 in), corn type (1)
Tweeter: 25 mm (1 in), dome type (1)
Midrange: 130 mm (5.25 in), corn type (1)
Tweeter: 25 mm (1 in), dome type (1)
Rated impedance 4
ohms
Maximum input power 100
watts
Sensitivity
89 dB (2.83 V/m)
Frequency response
42 Hz - 60,000 Hz
Cross over frequency
400 Hz, 4,000 Hz (multi-slope network)
Dimensions (w/h/d)
Approx. 280 mm × 980 mm × 410 mm
(11
(11
1
/
8
in × 38
5
/
8
in × 16
1
/
4
in)
Mass
Approx. 38 kg (84 lb)
Supplied accessories
Operating Instructions (1)
Warranty card (1)
Cleaning cloth (1)
Warranty card (1)
Cleaning cloth (1)
Design and specifications are subject to change without notice.
SS-AR2
2
SECTION 1
SERVICING NOTES
ABOUT HANDLING OF A SPEAKER UNIT
Please place the corn side of a speaker unit upside down, and do
not put on a fl oor etc. directly.
When you place the corn side upside down and you place it, please
use the parts attached to a new speaker unit as a pedestal, and put
them on a fl oor etc.
(Refer to the following fi gure)
Please place the corn side of a speaker unit upside down, and do
not put on a fl oor etc. directly.
When you place the corn side upside down and you place it, please
use the parts attached to a new speaker unit as a pedestal, and put
them on a fl oor etc.
(Refer to the following fi gure)
ABOUT THE SOLDER USED FOR REPAIR
Use the following solder, when you use solder by repair.
Part No. J-2501-310-A Unleaded solder (NSe-SOLDER)
Use the following solder, when you use solder by repair.
Part No. J-2501-310-A Unleaded solder (NSe-SOLDER)
NOTE THE SPEAKER UNIT REPLACING
When only left side or right side exchanges SPEAKER UNIT,
a sound quality difference may occur in right and left. When
SPEAKER UNIT of either one side is exchanged, it recommends
also exchanging simultaneously SPEAKER UNIT arranged in the
same position of the side opposite to.
When only left side or right side exchanges SPEAKER UNIT,
a sound quality difference may occur in right and left. When
SPEAKER UNIT of either one side is exchanged, it recommends
also exchanging simultaneously SPEAKER UNIT arranged in the
same position of the side opposite to.
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. GRILLE
FRAME
ASSY
(Page
3)
2-3. SPEAKER (16 cm) (UNIT ASSY)
(WOOFER) (SP1, SP2)
(Page
3)
2-5. SPEAKER (13 cm) UNIT ASSY (MID RANGE) (SP3),
MOUNT BOARD (MID) ASSY (MBM1)
(Page
4)
2-6. SPEAKER (2.5 cm) UNIT ASSY (TWEETER) (SP4),
MOUNT BOARD (TM) ASSY (MBT1)
(Page
5)
2-4. MOUNT BOARD (WO) ASSY
(MBW1)
(Page
(MBW1)
(Page
4)
2-7.
TERMINAL BOARD
(Page
5)
Ver. 1.1
SS-AR2
3
Note: Follow the disassembly procedure in the numerical order given.
2-2. GRILLE FRAME ASSY
1 total eight bosses
2 grille frame assy
2-3. SPEAKER (16 cm) (UNIT ASSY) (WOOFER) (SP1, SP2)
1 five screws
(4
u 25)
6 five screws
(4
u 25)
3 terminal (+) (green)
(W1
+)
8 terminal (+) (green)
(W2
+)
speaker
terminals
position
terminals
position
speaker
terminals
position
terminals
position
4 terminal (−)
(green/black)
(W1
(W1
−)
9 terminal (−) (green/black)
(W2
−)
2 Remove the speaker (16 cm) (unit assy)
in the direction of an arrow.
7 Remove the speaker (16 cm) (unit assy)
in the direction of an arrow.
5 speaker (16 cm) (unit assy)
(woofer: lower) (SP1)
0 speaker (16 cm)
(unit
assy)
(woofer:
upper)
(SP2)
speaker
terminals
terminals
Note: Check the position
of speaker terminals.
SS-AR2
4
2-4. MOUNT BOARD (WO) ASSY (MBW1)
1 terminal (+) (orange)
6 lead wire (+)
(white)
7 lead wire (−)
(white/black)
3 tapping screw
(BV3.5)
2 terminal (−) (gray)
4 Remove the mount board (WO) assy
in the direction of an arrow.
8 mount board (WO) assy
(MBW1)
5 Remove two solders.
2-5. SPEAKER (13 cm) UNIT ASSY (MID RANGE) (SP3), MOUNT BOARD (MID) ASSY (MBM1)
1 five screws
(4
u 25)
2 Remove the speaker (13 cm) unit assy
in the direction of an arrow.
3 terminal (+)
(white)
(M
(M
+)
qs lead wire (+) (orange)
(IN
+)
qd lead wire (+) (gray)
(IN
−)
7 terminal (+)
(blue)
8 terminal (+) (brown)
4 terminal (−) (white/black)
(M
−)
5 speaker (13 cm)
unit
assy
(mid
range)
(SP3)
9 tapping screw
(BV3.5)
0 Remove the mount board (MID) assy
in the direction of an arrow.
qa Remove two solders.
qf mount board
(MID)
assy
(MBM1)
speaker
terminals
position
terminals
position
6
acoustic absorbent
Note
2:
When installing the acoustic
absorbent, make it stick so
that an air layer may not be
made between walls.
Note 1: Check the position
of speaker terminals.
speaker terminals