SCD-XE597 (serv.man2) - Sony Audio Service Manual (repair manual). Page 3

3

After parts to the circuit (OPTICAL PICK-UP (DBU-3), RF
BOARD, MAIN BOARD, EEPROM (IC702), MASTERCOM
(IC705), DSP (IC706), so on) are replaced, readjusting is necessary.

1. While pressing [PUSH ENTER] button and [MENU] buttons,

press the [POWER] button to turn the set on.
“DIAG MODE”  is displayed on the screen.

2. Select “81 SYS-F VER” by tuning  l AMS L  knob.
3. Press [PUSH ENTER] button.
4. Check the version of ROM.

“SYS. VER X.XX” is displayed.

5. Select “82 I/F-F VER”

“I/F VER X.XX” is displayed.
Automatically return “81 SYS-F VER”

This checking must be performed before any other checking.

Use the following disc on this check.
SATD-S4:   PART No. J-2501-184-A
SATD-S5:   PART No. J-2501-215-A
Procedure:

1. While pressing [PUSH ENTER] button and [MENU] buttons,

press the [POWER] button to turn the set on.
“DIAG MODE”  is displayed on the screen.

2. Push the  Z  button to open the tray.
3. Load CD to tray.
4. Push the  Z  button to close the tray.
5. Turn “JOG DIAL” clockwise until “B0” and press the [PUSH

ENTER] (Used time : 7 sec) “FFFF” is displayed.

6. Turn “JOG DIAL” clockwise until “B1” and press the [PUSH

ENTER].
Display shows “-9” and the numbering is counting down until
“-0” lastly, “****” (4 DIGITS VALUE) appears. (Used time :
33 sec)

7. Turn “JOG DIAL” clockwise until “B2” and press the [PUSH

ENTER].
Display shows the last number that appear at. STEP NO.7.
Confirm that the value is “08D0”>THE VALUE>“04D0”

8. Push the  Z  button to open the tray.
9. Unload CD from tray.
10. Push the  Z  button to close the tray.
11. Press the [POWER] button to turn the set off. (Do not continue

with another test mode without power off.)

Use the following hybrid disc on this check.
HLXA-509 : PART No. J-6090-090-A
SACD HYBRID DISC (MARKET DISC)
Connection:

1. Press the  Z  button.
2. Insert SACD hybrid disc (market disc).
3. Connect the oscilloscope to pin 27 and pin31 of CN702.
4. Observe the MIRR waveform immediately after the disc

chucking is completed when disc identification is made.

MIRR signal waveform

5. Read the measurement of 

∆ 

T.

IF 7.5ms <

∆

 T<9.7ms> OK

OTHERS>NG

6. When the system version number is before ver.1.24, and if the

MIRR waveform is NG (No Good), change the values of R892
and R893, and then repeat step4 and after.
9.7 ms< 

∆ 

t

R892/R893  120 k

Ω

 

→

 110 k

Ω

 (1-218-741-11)

∆

 t< 6.9 ms

R892/R893  120 k

Ω

 

→

 130 k

Ω

 (1-218-743-11)

Be sure to set the unit to the specified modes as stated in the steps
below after sampling inspections by the QA dept.
Or before shipping.
Procedure:

1. While pressing [PUSH ENTER] and [MENU] buttons, press the

[POWER] button to turn the set on.
“DIAG MODE” is displayed in the screen.

2. Turn jog until the specified mode (According to version) is

displayed:
a) “8D SETUP” : CEL
b) “8F SETUP” : U & OTHERS

3. Press jog one single time.

“INIT START” is displayed and Mode setting for shipping
starts.

4. Wait until “INITIAL OK” appears on the display.
5. By this operation, the unit is initialized as follows:

6. After 2 to 3 sec., Press the  [POWER]  button to turn the set off.

Note : When EEPROM (IC702) is replaced, the initialization

is necessary.

+
–

MAIN board

CN702 (PIN27)

CN702 (PIN31)

oscilloscope

1V/DIV, 5ms/DIV

T

PLAY MODE

ALL DISCS

COMMAND MODE

CD 1

REPEAT

OFF

SACD/CD

SACD

M/2ch

MULTI