Read Sony SA-WGT5D Service Manual online
SA-WGT5D
6
4. Press the [S2
+]/[S1 –
] buttons to select target destina-
tion, and press the [ENTER] button.
5. The message “RESET” is displayed on the fl uorescent indica-
tor tube, then start the initialization (power off (demonstration
mode)
mode)
→ power on → power off (demonstration mode)) auto-
matically.
Note
5: Don’t disconnect the power-supply cord during the initializa-
tion.
Screen display
6. When the initialization is completed, the destination change is
completed.
7. When checking the setting destination, refer to the “PANEL TEST
MODE” on page 41.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
AEP
AEP
: European (Except for UK, Ireland), East Europe, Moldova
models
AR :
Argentina
model
AUS : Australian, New Zealand models
E4
E4
: Middle East (Except for Iraq, Kuwait, Saudi Arabia, UAE),
African (Except for Kenya, Nigeria, Tanzania) models
EA
: Middle East (Iraq, Kuwait, Saudi Arabia, UAE), African
(Kenya, Nigeria, Tanzania) models
LA
: Latin American (Except for Brazilian, Argentina) model
RU
: Russian, Belarus, Kazakhstan models
SP6 :
Singapore, Malaysia, Indonesia, Philippines, Vietnam models
UK
: UK, Ireland models
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
All of the units included in the MHC-GT5D (SA-WGT5D/SS-
GT5DB/Remote control) are required to confi rming operation of
SA-WGT5D. Check in advance that you have all of the units.
ERATION
All of the units included in the MHC-GT5D (SA-WGT5D/SS-
GT5DB/Remote control) are required to confi rming operation of
SA-WGT5D. Check in advance that you have all of the units.
CHECKING THE OPERATION AFTER REPAIR
After repair completion, connect the “iPod”, “Walkman”, “smart-
phone” etc. corresponding to this unit, and check the operation of
playback, recording, charge, etc.
After repair completion, connect the “iPod”, “Walkman”, “smart-
phone” etc. corresponding to this unit, and check the operation of
playback, recording, charge, etc.
NOTE OF REPLACING THE SW-PARTY-LED BOARD
When the SW-PARTY-LED board is defective, replace the com-
plete mounted board.
When the SW-PARTY-LED board is defective, replace the com-
plete mounted board.
NOTE OF REPLACING THE SW-RGB-LED-L BOARD
When the SW-RGB-LED-L board is defective, replace the com-
plete mounted board.
When the SW-RGB-LED-L board is defective, replace the com-
plete mounted board.
NOTE OF REPLACING THE SW-RGB-LED-R BOARD
When the SW-RGB-LED-R board is defective, replace the com-
plete mounted board.
When the SW-RGB-LED-R board is defective, replace the com-
plete mounted board.
NOTE OF REPLACING THE MS-476 BOARD
When the MS-476 board is defective, replace the LOADING
COMPLETE ASSY (T) (Ref. No. CDM1).
When the MS-476 board is defective, replace the LOADING
COMPLETE ASSY (T) (Ref. No. CDM1).
NOTE OF REPLACING THE IC104 TO IC106, IC402 TO
IC404 ON THE ARAGON-MOTHER BOARD
IC104 to IC106, IC402 to IC404 on the ARAGON-MOTHER
board cannot replace with single. When these parts are damaged,
replace the complete mounted board.
IC404 ON THE ARAGON-MOTHER BOARD
IC104 to IC106, IC402 to IC404 on the ARAGON-MOTHER
board cannot replace with single. When these parts are damaged,
replace the complete mounted board.
NOTE OF REPLACING THE IC2004, IC2005 AND
IC2501 ON THE D-AMP BOARD
IC2004, IC2005 and IC2501 on the D-AMP board cannot replace
with single. When these parts are damaged, replace the complete
mounted board.
IC2004, IC2005 and IC2501 on the D-AMP board cannot replace
with single. When these parts are damaged, replace the complete
mounted board.
NOTE OF REPLACING THE IC002 ON THE POWER
BOARD
IC002 on the POWER board cannot replace with single. When this
part is damaged, replace the complete mounted board.
BOARD
IC002 on the POWER board cannot replace with single. When this
part is damaged, replace the complete mounted board.
Ver. 1.1
Click on the first or last page to see other SA-WGT5D service manuals if exist.