Read Sony SA-WCT780 Service Manual online
SA-WCT780
5
ADVANCE PREPARATION WHEN CONFIRMING OP-
ERATION
All of the units included in the HT-CT780 (SA-WCT780/SA-
CT780/Remote control) are required to confi rming operation of
SA-WCT780. Check in advance that you have all of the units.
ERATION
All of the units included in the HT-CT780 (SA-WCT780/SA-
CT780/Remote control) are required to confi rming operation of
SA-WCT780. Check in advance that you have all of the units.
NOTE OF REPLACING THE SW-KEY BOARD
When the SW-KEY board is defective, replace the complete
mounted board.
When the SW-KEY board is defective, replace the complete
mounted board.
NOTE OF REPLACING THE IC100 ON THE SW-MAIN
BOARD
IC100 on the SW-MAIN board cannot replace with single. When
this part is damaged, replace the complete mounted board.
BOARD
IC100 on the SW-MAIN board cannot replace with single. When
this part is damaged, replace the complete mounted board.
NOTE OF REPLACING THE IC104 ON THE SW-MAIN
BOARD AND THE COMPLETE SW-MAIN BOARD
When IC104 on the SW-MAIN board and the complete SW-MAIN
board are replaced, it is necessary to spread the compound between
the SW-MAIN board and the heat sink.
Spread the compound referring to the fi gure below.
BOARD AND THE COMPLETE SW-MAIN BOARD
When IC104 on the SW-MAIN board and the complete SW-MAIN
board are replaced, it is necessary to spread the compound between
the SW-MAIN board and the heat sink.
Spread the compound referring to the fi gure below.
– SW-MAIN Board (Component Side) –
IC104
compound
NOTES ON THE WIRELESS CONNECTION (LINK) AFTER
REPAIRS ARE COMPLETE
When the parts below is replaced, the wireless connection (LINK)
of the Bar speaker and Subwoofer will be disconnected.
Before returning repaired products to the customer, follow the pro-
cedure below to LINK the Bar speaker and Subwoofer.
Also, if only the Bar speaker or Subwoofer is brought in for repair
and the parts below are replaced, be sure to inform the customer
when returning the repaired products that the customer must LINK
the Bar speaker and Subwoofer.
(Indicate that the LINK procedure is described in the operating
instructions)
REPAIRS ARE COMPLETE
When the parts below is replaced, the wireless connection (LINK)
of the Bar speaker and Subwoofer will be disconnected.
Before returning repaired products to the customer, follow the pro-
cedure below to LINK the Bar speaker and Subwoofer.
Also, if only the Bar speaker or Subwoofer is brought in for repair
and the parts below are replaced, be sure to inform the customer
when returning the repaired products that the customer must LINK
the Bar speaker and Subwoofer.
(Indicate that the LINK procedure is described in the operating
instructions)
Parts in which the LINK will be disconnected due to re-
placement:
•
placement:
•
Complete SW-MAIN board
•
RF modulator (SWA12-4V RX) (Ref. No. RF1)
Linking the system (Link to the Subwoofer)
Set up the wireless subwoofer
connection again.
connection again.
1
Press MENU.
2
Select [WS] with j (select), then
press ENTER.
press ENTER.
3
Select [LINK] with j (select), then
press ENTER.
press ENTER.
4
When [START] appears on the
display, press ENTER.
[SEARCH] appears, and the Bar
Speaker searches for a device that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function while
searching for a device, press BACK.
display, press ENTER.
[SEARCH] appears, and the Bar
Speaker searches for a device that
can be used with Link. Proceed to
the next step within 1 minute.
To quit the Link function while
searching for a device, press BACK.
5
Press LINK on the subwoofer.
The on/standby indicator on the
subwoofer lights up in green. [OK]
appears on the display of the Bar
Speaker.
If [FAILED] appears, check to ensure
the subwoofer is turned on and
perform the process again from
step 1.
The on/standby indicator on the
subwoofer lights up in green. [OK]
appears on the display of the Bar
Speaker.
If [FAILED] appears, check to ensure
the subwoofer is turned on and
perform the process again from
step 1.
6
Press MENU.
The menu turns off.
The menu turns off.
THE ON/STANDBY INDICATOR FLASHES IN RED
– Press the Ò/Æ (on/standby)
button of the subwoofer to turn
off the power and check
whether the ventilation opening
of the subwoofer is blocked or
not.
off the power and check
whether the ventilation opening
of the subwoofer is blocked or
not.
Ç
Click on the first or last page to see other SA-WCT780 service manuals if exist.