Read Sony SA-VE155 / SA-WMS155 / SS-MS155 Service Manual online
1
Ver 1.0 2004. 05
SERVICE MANUAL
AEP Model
UK Model
E Model
SS-MS155
(front, center and surround speakers)
Speaker system
Full range, magnetically
shielded
shielded
Speaker units
7 cm, cone type
Enclosure type
Closed type
Rated impedance
8 ohms
Power handling capacity
Maximum input power: 100 W
Sensitivity level
Maximum input power: 100 W
Sensitivity level
83 dB (1 W, 1 m)
Frequency range
120 Hz - 20,000 Hz
Dimensions (w/h/d)
Approx. 91
× 96 × 102 mm,
including front grille
Mass
Approx. 650 g each
SPECIFICATIONS
SA-WMS155
(subwoofer)
Speaker system
Active subwoofer,
magnetically shielded
magnetically shielded
Speaker unit
Woofer: 16 cm, cone type
Enclosure type
Bass refl ex
Reproduction frequency range
32 Hz - 200 Hz
Continuous RMS power output
55 W (4 ohms, 100 Hz,
10 % THD)
10 % THD)
Input
LINE IN (input pin jack)
LINE IN (input pin jack)
General
Power requirements
Power requirements
220 - 240 V AC, 50/60 Hz
Power consumptions
45 W
Dimensions (w/h/d)
E model:
Approx. 210
Approx. 210
× 355 × 335
mm
AEP, UK model:
Approx. 210
AEP, UK model:
Approx. 210
× 355 × 330
mm
Mass
Approx. 8 kg
• SA-VE155 consists of the following models respectively.
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
9-877-869-01
2004E04-1
© 2004. 05
MICRO SATELLITE SPEAKER SYSTEM
SA-VE155/WMS155/
SS-MS155
SUBWOOFER
SA-WMS155
FRONT, CENTER AND
SURROUND SPEAKER
SURROUND SPEAKER
SS-MS155
SA-WMS155
SS-MS155
Supplied accessories
Foot pads (20)
Audio connecting cord (1)
Speaker connecting cords, 10 m (2)
Speaker connecting cords, 3.5 m (3)
Audio connecting cord (1)
Speaker connecting cords, 10 m (2)
Speaker connecting cords, 3.5 m (3)
Design and specifi cations are subject to change
without notice.
without notice.
2
SA-VE155/WMS155/SS-MS155
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
•
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 3
2. DIAGRAMS
2-1. Note for Printed Wiring Boards and
Schematic Diagrams ............................................................ 3
2-2. Circuit Boards Location ...................................................... 3
2-3. Printed Wiring Boards (SA-WMS155) ............................... 4
2-4. Schematic Diagram (SA-WMS155) ................................... 5
2-5. IC Block Diagram ............................................................... 6
Schematic Diagrams ............................................................ 3
2-2. Circuit Boards Location ...................................................... 3
2-3. Printed Wiring Boards (SA-WMS155) ............................... 4
2-4. Schematic Diagram (SA-WMS155) ................................... 5
2-5. IC Block Diagram ............................................................... 6
3. EXPLODED VIEWS
.......................................................... 7
4. ELECTRICAL PARTS LIST
........................................... 8
3
3
SA-VE155/WMS155/SS-MS155
SA-VE155/WMS155/SS-MS155
2-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
2-2. CIRCUIT BOARDS LOCATION
SECTION 2
DIAGRAMS
SECTION 1
GENERAL
LOCATION OF CONTROL
This section is extracted
from instruction manual.
from instruction manual.
English
WARNING
To prevent fi re or shock hazard, do not expose the
unit to rain or moisture.
To prevent fi re, do not cover the ventilation of the apparatus
with news papers, table-cloths, curtains, etc. And don’t place
lighted candles on the apparatus.
To prevent fi re or shock hazard, do not place objects fi lled with
liquids, such as vases, on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualifi ed personnel only.
unit to rain or moisture.
To prevent fi re, do not cover the ventilation of the apparatus
with news papers, table-cloths, curtains, etc. And don’t place
lighted candles on the apparatus.
To prevent fi re or shock hazard, do not place objects fi lled with
liquids, such as vases, on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualifi ed personnel only.
Do not install the appliance in a confi ned space, such as a
bookcase or built-in cabinet.
bookcase or built-in cabinet.
About this manual
The SA-VE155 is a 5.1 channel speaker system consisting of
two front speakers, one center speaker, two surround speakers,
and one subwoofer. It supports Sony Digital Cinema Sound,
Dolby* Pro Logic, and Dolby Digital etc., and is thus geared
towards the enjoyment of movies.
two front speakers, one center speaker, two surround speakers,
and one subwoofer. It supports Sony Digital Cinema Sound,
Dolby* Pro Logic, and Dolby Digital etc., and is thus geared
towards the enjoyment of movies.
* “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Precautions
On safety
• Before operating the system, be sure that the operating
• Before operating the system, be sure that the operating
voltage of the system is identical with that of your local
power supply.
power supply.
• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off.
the unit itself has been turned off.
• Unplug the system from the wall outlet if it is not to be used
for an extended period of time. To disconnect the cord, pull
the cord by grasping the plug. Never pull the cord itself.
the cord by grasping the plug. Never pull the cord itself.
• Should any liquid or solid object fall into the system, unplug
the system’s power cord and have the system checked by
qualifi ed personnel before operating it any further.
qualifi ed personnel before operating it any further.
• AC power cord must be changed only at the qualifi ed service
shop.
On operation
• Do not drive the speaker system with a continuous wattage
• Do not drive the speaker system with a continuous wattage
exceeding the maximum input power of the system.
• If the polarity of the speaker connections are not correct,
the bass tones will be weak and the position of the various
instruments obscure.
instruments obscure.
• Contact between bare speaker wires at the speaker terminals
may result in a short circuit.
• Before connecting, turn off the amplifi er to avoid damaging
the speaker system.
• The speaker grille cannot be removed. Do not attempt to
remove the grille on the speaker system. If you try to remove
it, you may damage the speaker.
it, you may damage the speaker.
• The volume level should not be turned up to the point of
distortion.
If you encounter color irregularity on a
nearby TV screen
This speaker system is magnetically shielded to allow it to be
installed near a TV set. However, color irregularities may still
be observed on certain types of TV sets.
nearby TV screen
This speaker system is magnetically shielded to allow it to be
installed near a TV set. However, color irregularities may still
be observed on certain types of TV sets.
If color irregularity is observed...
c
Turn off the TV set, then turn it on again after 15 to 30
minutes.
If color irregularity is observed again...
c
Place the speakers further away from the TV set.
If howling occurs
Reposition the speakers or turn down the volume on the
amplifi er.
Reposition the speakers or turn down the volume on the
amplifi er.
On placement
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
— Extremely hot or cold
— Dusty or dirty
— Very humid
— Subject to vibrations
— Subject to direct sunlight
— Dusty or dirty
— Very humid
— Subject to vibrations
— Subject to direct sunlight
• Use caution when placing the speaker on a specially
treated (waxed, oiled, polished, etc.) fl oor, as staining or
discoloration may result.
discoloration may result.
On cleaning
Clean the speaker cabinets with a soft cloth lightly moistened
with a mild detergent solution or water. Do not use any type
of abrasive pad, scouring powder or solvent such as alcohol or
benzine.
Clean the speaker cabinets with a soft cloth lightly moistened
with a mild detergent solution or water. Do not use any type
of abrasive pad, scouring powder or solvent such as alcohol or
benzine.
If you have any questions or problems concerning your speaker
system, please consult your nearest Sony dealer.
system, please consult your nearest Sony dealer.
Hooking up the system
Connect the speaker system to the speaker output terminals of
an amplifi er (A).
Make sure power to all components (included the subwoofer)
is turned off before starting the hook-up.
an amplifi er (A).
Make sure power to all components (included the subwoofer)
is turned off before starting the hook-up.
Notes (B)
• Make sure the plus (+) and the minus (–) terminals on the
• Make sure the plus (+) and the minus (–) terminals on the
speakers are matched to the corresponding plus (+) and
minus (–) terminals on the amplifi er.
minus (–) terminals on the amplifi er.
• Be sure to tighten the screws of the speaker terminals
securely as loose screws may become a source of noise.
• Make sure all connections are fi rm. Contact between bare
speaker wires at the speaker terminals may cause a short
circuit.
circuit.
• For details regarding the connections on the amplifi er side,
refer to the manual that was provided with your amplifi er.
Tip
Black or black striped wires are minus (–) in polarity, and
should be connected to the minus (–) speaker terminals.
Black or black striped wires are minus (–) in polarity, and
should be connected to the minus (–) speaker terminals.
A
eE Ee
E
e
LINE IN
WOOFER OUT
FRONT
CENTER
SURROUND
R
R
L
L
Ee
Ee
Ee
Ee
Ee
Front (Right)
Avant (droite)
Avant (droite)
Center
Centre
Centre
Subwoofer
Caisson de grave
Caisson de grave
Front (Left)
Avant (gauche)
Avant (gauche)
Surround
(Right)
Effet surround
(droite)
(Right)
Effet surround
(droite)
Surround
(Left)
Effet surround
(gauche)
(Left)
Effet surround
(gauche)
Ampli er
Ampli cateur
Ampli cateur
3.5m
3,5m
3,5m
3.5m
3,5m
3,5m
3.5m
3,5m
3,5m
10m
10m
E
e
E
e
E
e
E
e
B
Positioning the speakers
Location of each speaker (C)
Each speaker should face the listening position. Better
surround effect will result if all speakers are set at the same
distance from the listening position.
Place the front speakers at a suitable distance to the left and
right of the television.
Place the subwoofer on either side of the television.
Place the center speaker on the top-center of the TV set.
The placement of surround speakers greatly depends on the
confi guration of the room. The surround speakers may be
placed on both sides of the listening position A or behind the
listening position B.
surround effect will result if all speakers are set at the same
distance from the listening position.
Place the front speakers at a suitable distance to the left and
right of the television.
Place the subwoofer on either side of the television.
Place the center speaker on the top-center of the TV set.
The placement of surround speakers greatly depends on the
confi guration of the room. The surround speakers may be
placed on both sides of the listening position A or behind the
listening position B.
Setting the speakers
To prevent speaker vibration or movement while listening,
attach the supplied foot pads to the bottom four corners of the
front speakers, center speaker and surround speakers (D).
attach the supplied foot pads to the bottom four corners of the
front speakers, center speaker and surround speakers (D).
Setting the center speaker (E)
Set the center speaker fi rmly on top of the TV set, making sure
it is completely level.
Set the center speaker fi rmly on top of the TV set, making sure
it is completely level.
Setting the speakers using the optional speaker
stands (F)
For greater fl exibility in the positioning of the speakers, use the
optional WS-FV11 or WS-WV10D speaker stand (available
only in certain countries).
stands (F)
For greater fl exibility in the positioning of the speakers, use the
optional WS-FV11 or WS-WV10D speaker stand (available
only in certain countries).
To hang the front, center and surround speakers
with a hook (not supplied) on the wall (G)
You are responsible for the proper selection and use of
mounting hardware that you purchase at hardware stores, and
for the proper and safe mounting of the speakers.
with a hook (not supplied) on the wall (G)
You are responsible for the proper selection and use of
mounting hardware that you purchase at hardware stores, and
for the proper and safe mounting of the speakers.
Tip
The height of the front speakers should be adjusted to about the
center of the TV screen (H).
The height of the front speakers should be adjusted to about the
center of the TV screen (H).
Setting the amplifi er
When connecting to an amplifi er with internal multi channel
decoders (Dolby Digital, DTS**, etc.), you should use the
setup menus for the amplifi er to specify the parameters of your
speaker system.
See the table below for the proper settings. For details on the
setting procedure, refer to the manual that was provided with
your amplifi er.
decoders (Dolby Digital, DTS**, etc.), you should use the
setup menus for the amplifi er to specify the parameters of your
speaker system.
See the table below for the proper settings. For details on the
setting procedure, refer to the manual that was provided with
your amplifi er.
Speaker setup
For Set to
Front speakers SMALL
Center speaker SMALL
Surround speakers SMALL
Subwoofer ON (or YES)
If you use the amplifi er with adjustable crossover frequency,
it is recommended to select 150 Hz (or close to this fi gure) as
the crossover frequency for your front, center and surround
speakers.
it is recommended to select 150 Hz (or close to this fi gure) as
the crossover frequency for your front, center and surround
speakers.
** “DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Sys tems, Inc.
Listening to the sound (
I
)
First, turn down the volume on the amplifi er. The volume
should be set to minimum before you begin playing the
program source.
should be set to minimum before you begin playing the
program source.
1
Turn on the amplifi er and select the program
source.
2
Press POWER on the subwoofer.
The POWER indicator on the subwoofer
lights up green.
lights up green.
3
Play the program source.
Adjusting the subwoofer (
I
)
Rotate LEVEL to adjust the volume.
Set the volume level to best suit your pref er ence
according to the program source.
according to the program source.
Notes
• Some amplifi er functions for enhancing the sound may cause
• Some amplifi er functions for enhancing the sound may cause
distortion in the subwoofer. If such distortion occurs, turn off
those functions.
those functions.
• To enjoy high-quality sound, do not turn the subwoofer
volume too high.
Troubleshooting
Should you encounter a problem with your speaker system,
check the following list and take the indicated measures. If the
problem persists, consult your nearest Sony dealer.
check the following list and take the indicated measures. If the
problem persists, consult your nearest Sony dealer.
There is no sound from the speaker system.
• Make sure all the connections have been correctly
made.
• Make sure the volume on the amplifi er has been
turned up properly.
• Make sure the program source selector on the
amplifi er is set to the proper source.
• Check if headphones are connected. If they are,
disconnect them.
There is distortion in the subwoofer sound
output.
output.
• Check if any sound-enhancing functions have been
activated on the amplifi er. If they have, turn them
off.
off.
There is hum or noise in the speaker output.
• Make sure all the connections have been correctly
made.
• Make sure none of the audio components are
positioned too close to the TV set.
The sound has suddenly stopped.
• Make sure all the connections have been correctly
made. Contact between bare speaker wires at the
speaker terminals may cause a short circuit.
speaker terminals may cause a short circuit.
H
F
WS-WV10D
(for front, center and surround speakers)
(pour les enceintes avant, centrale et ‡ effet
surround)
(for front, center and surround speakers)
(pour les enceintes avant, centrale et ‡ effet
surround)
WS-FV11
E
Foot pads
Tampons
autocollants
Tampons
autocollants
G
Hook
Crochet
Crochet
I
POWER indicator
Voyant POWER
Voyant POWER
LINE IN
LEVEL
POWER
C
Front (Right)
Avant (droite)
Avant (droite)
Center
Centre
Centre
Subwoofer
Caisson de grave
Caisson de grave
Surround (Right)
Effet surround (droite)
Effet surround (droite)
Front (Left)
Avant
(gauche)
Avant
(gauche)
Surround (Left)
Effet surround (gauche)
Effet surround (gauche)
A
A
B
B
D
Foot pads
Tampons autocollants
Tampons autocollants
Note (Singaporean model only)
Protection circuit is contained in the satellite speakers. If the
speakers are overdriven for certain minutes, the protection
circuit will automatically reduce the sound volume. In the case,
stop the program source for 2-3 minutes. Before playing the
source again, turn down the volume level of the amplifi er.
Protection circuit is contained in the satellite speakers. If the
speakers are overdriven for certain minutes, the protection
circuit will automatically reduce the sound volume. In the case,
stop the program source for 2-3 minutes. Before playing the
source again, turn down the volume level of the amplifi er.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in Ω and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
For printed wiring boards.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
• A : B+ Line.
• B : B– Line.
• Voltages are dc with respect to ground under no-signal
• B : B– Line.
• Voltages are dc with respect to ground under no-signal
(detuned) conditions.
no mark : Power on
• Voltages are taken with a VOM (Input impedance 10 MΩ).
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Signal path.
F
: AUDIO
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
Replace only with part number specified.
TRANSFOMER board
POWER board
CONTROL board
POWER SWITCH board
LED board
4
4
SA-VE155/WMS155/SS-MS155
SA-VE155/WMS155/SS-MS155
1
A
B
C
D
E
F
G
H
I
J
2
3
4
5
6
7
8
9
10
11
12
13
14
WHT
WHT
RED
C813
C614
CN802
CN803
AC IN
BC301
D301
D301
(POWER)
C804
J21
J24
R620
Q604
Q603
Q602
E MODEL
E MODEL
R614
R616
R616
C612
R602
R613
R603
C518
VR501
SP1
SPEAKER
4Ω
LEVEL
S801
POWER
J501
LINE
LINE
IN
CN501
WHT
BLK
WHT
RED
BLK
WHT
RED
J26
J25
RED
BLK
BLK
R618
R804
R802
BC601
R615
RED
BLU
BRN
RED
WHT
WHT
1-862-214-
11
1-862-217-
11
1-862-216-
11
1-862-218-
11
1-862-215-
11
C803
C810
S801
BC802
C808
C806
Q801
Q802
R803
R801
Q605
D803
D802
C805
C807
C602
C607
C801
J16
CN301
J15
D801
R605
J23
J22
Q601
C613
R610
C611
J10
J8
J7
C802
J11
J19
RLY601
J12
CN601
C608
J13
BLU
BRN
TH601
R601
R511
R510
J6
J5
IC502
IC501
C512
R509
R506
R508
R512
R504
R507
R501
J501
R503
C601
Q606
C603
R604
IC601
J20
C501
C508
C507
C502
R502
C504
R505
C506
J4
J2
C511
C503
C517
C505
J1
C509
C510
C516
C513
C514
J3
C606
J17
J14
C610
J8
J7
R619
R301
R608
R609
D602
D601
C604
C605
C809
C815
R607
BC801
D603
C814
RED
1
2
2
10
14
1
15
1
2
1
1
2
1
2
1
3
5
1
2
1
3
WHT
RED
WHT
WHT
F801
CN801
T801
3
1
LED BOARD
TRANSFORMER BOARD
POWER BOARD
CONTROL BOARD
POWER SWITCH BOARD
8
5
1
4
1
4
8
4
1
5
2-3. PRINTED WIRING BOARDS (SA-WMS155) • Refer to page 3 for Circuit Boards Location.
: Uses unleaded solder.
D301
B-2
D601
I-9
D602
I-9
D603
J-8
D801
I-7
• Semiconductor Location
Ref. No.
Location
Ref. No.
Location
Ref. No.
Location
D802
D-9
D803
D-8
IC501
H-12
IC502
G-12
IC601
F-6
Q601
G-9
Q602
D-8
Q603
D-8
Ref. No.
Location
Q604
D-7
Q605
E-8
Q606
E-8
Q801
E-9
Q802
E-8