Read Sony SA-PSD5 / SA-WPSD5 / SS-SPSD5 Service Manual online
4
SA-PSD5/WPSD5/SS-SPSD5
SECTION 2
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
2-1. Circuit Boards Location
KEY-L board
POWER board
ADJ board
INPUT board
KEY-R board
PRE AMP board
DIGITAL board
SP board
SIRCS board
LCD board
Note on Schematic Diagram:
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. p: pF.
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
• All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
f
: internal component.
•
C
: panel designation.
Note on Printed Wiring Board:
• X
: parts extracted from the component side.
• Y
: parts extracted from the conductor side.
•
x
: parts mounted on the conductor side.
•
a
: Through hole.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
• Indication of transistor
Caution:
Pattern face side:
Pattern face side:
Parts on the pattern face side seen from
(SIDE A)
the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(SIDE B)
the parts face are indicated.
Note:
The components identi-
fied by mark
The components identi-
fied by mark
0
or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
Les composants identifiés par
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Q
C
These are omitted
E
B
•
A
: B+ Line.
•
B
: B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: AUDIO (ANALOG)
J
: AUDIO (DIGITAL)
• Abbreviation
CND : Canadian model.
SP
SP
: Singapore model.
C
These are omitted
E
B
1
IC815
wz
XOUT
6.5
Vp-p
Vp-p
2
IC815
w;
XMCK
81.4 ns
3
IC815
qg
LRCK
6
IC701
qd
XOUT
4
IC815
qf
BCK
5
IC815
qd
CKOUT
6.1
Vp-p
Vp-p
5.6
Vp-p
Vp-p
5.0
Vp-p
Vp-p
5.6
Vp-p
Vp-p
4.7
Vp-p
Vp-p
81.4 ns
325 ns
81.4 ns
20.8
µ
s
62.5 ns
• WAVEFORMS
Click on the first or last page to see other SA-PSD5 / SA-WPSD5 / SS-SPSD5 service manuals if exist.