SA-FT3H, SA-WFT3, SS-CNF3H, SS-FRF3H - Sony Audio Service Manual (repair manual)

sa-ft3h, sa-wft3, ss-cnf3h, ss-frf3h service manual
Model
SA-FT3H SA-WFT3 SS-CNF3H SS-FRF3H
Pages
20
Size
4.53 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
sa-ft3h-sa-wft3-ss-cnf3h-ss-frf3h.pdf
Date

Read Sony SA-FT3H / SA-WFT3 / SS-CNF3H / SS-FRF3H Service Manual online

1
Ver. 1.1  2007.04
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
E Model
SPECIFICATIONS
HOME THEATRE SPEAKER SYSTEM
SS-FRF3H
SA-FT3H/WFT3/
SS-CNF3H/FRF3H
SS-CNF3H
AUDIO POWER SPECIFICATIONS (US, CND model)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
With 6 ohm loads, from 28 – 200 Hz; rated 150 watts per
channel minimum RMS power, with no more than 10% total
harmonic distortion from 250 milliwatts to rated output.
SS-FRF3H (front/surround speakers)
Speaker system
2 way, magnetically shielded
Speaker units
Woofer: 10 cm, cone
type
Tweeter: 2.5 cm, balanced
dome type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
110 W
Sensitivity level
84 dB (1 W, 1 m)
Frequency range
140 Hz – 50,000 Hz
Dimensions (w/h/d)
Approx. 120 
× 360 × 32 mm
with table top stand
Approx. 120 
× 372 × 32 mm
(Diameter of base: 190 mm)
Mass
Approx. 0.9 kg
with table top stand
Approx. 0.95 kg
SS-CNF3H (center speaker)
Speaker system
2 way, magnetically shielded
Speaker units
Woofer: 8 cm (
× 2), cone
type
Tweeter: 2.5 cm,
dome type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
110 W
Sensitivity level
84 dB (1 W, 1 m)
Frequency range
150 Hz – 50,000 Hz
Dimensions (w/h/d)
Approx. 430 
× 88 × 32 mm
with table top stand
Approx. 430 
× 98 × 66 mm
Mass
Approx. 0.85 kg
with table top stand
Approx. 0.9 kg
• SA-FT3H is composed of following models.
COMPONENT MODEL NAME
FRONT/SURROUND SPEAKER
SS-FRF3H
CENTER SPEAKER
SS-CNF3H
SUBWOOFER
SA-WFT3
SA-WFT3
– Continued on next page –
9-879-802-02
2007D04-1
© 2007.04
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
2
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  
0
  OR  DOTTED  LINE
WITH  MARK  
0
  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
 À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE  DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
To Exposed Metal
Parts on Set
0.15
µ
F
1.5k
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale. The
Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
SA-WFT3 (subwoofer)
Speaker system
Active subwoofer,
magnetically shielded
Speaker units
Woofer: 15 cm (
× 2), cone
type
Enclosure type
Acoustically Loaded
Bass reflex
Reproduction frequency range
28 Hz – 200 Hz
Continuous RMS power output
150 W (6 ohms 100 Hz,
10% THD)
Input
LINE IN (input pin jack)
General
Power requirements
US, CND model:
120 V AC, 60 Hz
AEP, UK model:
230 V AC, 50/60 Hz
SP, MY model:
220 – 230 V AC, 50/60 Hz
Power consumptions
80 W
0.3 W (standby mode)
Dimensions (w/h/d)
Approx. 182 
× 477 × 353 mm
Mass
Approx. 12 kg
Supplied accessories
SA-FT3H:
Speaker cord (3.5 m) (3)
Speaker cord (10 m) (2)
Table top stand cover (4)
Table top stand base (4)
Center speaker stand base (1)
Center speaker stand adjuster (1)
Cushion (20)
Rear pad (10)
Screw (M5) (5)
Screw (M4) (2)
Screw (M3.5) (16)
SS-FRF3H:
Speaker cord (10 m) (1)
Table top stand base (1)
Table top stand cover (1)
Screw (M5) (1)
Screw (M3.5) (4)
Cushion (4)
Rear pad (2)
Design and specifications are subject to change without notice.
• Abbreviation
CND : Canadian model
SP
: Singapore model
MY : Malaysia model
SA-FT3H/WFT3/SS-CNF3H/FRF3H
3
SA-FT3H/WFT3/SS-CNF3H/FRF3H
TABLE OF CONTENTS
1. DISASSEMBLY
1-1.   Rear Panel Section .............................................................. 4
1-2.   Main Board, Power AMP Board ......................................... 5
2. DIAGRAMS
2-1.   Block Diagram .................................................................... 7
2-2.   Printed Wiring Boards – Main Section – ............................ 8
2-3.   Printed Wiring Boards – Control Section – ......................... 9
2-4.   Schematic Diagram – Main Section – ............................... 10
3. EXPLODED VIEWS
3-1.   Front/Surround Speaker Section (SS-FRF3H) .................. 11
3-2.   Center Speaker Section (SS-CNF3H) ............................... 12
3-3.   Subwoofer Section (1) (SA-WFT3) .................................. 13
3-4.   Subwoofer Section (2) (SA-WFT3) .................................. 14
4. ELECTRICAL PARTS LIST
......................................... 15
4
SA-FT3H/WFT3/SS-CNF3H/FRF3H
SECTION 1
DISASSEMBLY
• The equipment can be removed using the following procedure.
1-1. REAR PANEL SECTION
Note :
 Follow the disassembly procedure in the numerical order given.
1-1.
REAR PANEL SECTION 
(Page 4)
1-2.
MAIN BOARD,
POWER AMP BOARD
(Page 5)
SET
4
 BC901 (2P)
6
 CN101 (6P)
8
 rear panel section
7
 BC602 (2P)
5
 BC904 (3P)
1
 four tapping screws (1)
(3.5 
×
 20)
2
 four tapping screws (1)
(3.5 
×
 20)
3
Page of 20
Display

Download Sony SA-FT3H / SA-WFT3 / SS-CNF3H / SS-FRF3H Service Manual (Repair Manual)

Here you can read online and download Sony SA-FT3H / SA-WFT3 / SS-CNF3H / SS-FRF3H Service Manual in PDF. SA-FT3H / SA-WFT3 / SS-CNF3H / SS-FRF3H service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony SA-FT3H / SA-WFT3 / SS-CNF3H / SS-FRF3H Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.