Read Sony NWZ-WS613 / NWZ-WS615 Service Manual online
NWZ-WS613/WS615
4
NOTE FOR REPLACING THE REMOTE COMMAND-
ER (RMT-NWS10B) OR THE REMOTE COMMANDER
(RMT-NWS10B) LITHIUM BATTERY
For the remote commander (RMT-NWS10B) lithium battery, be
sure to follow the instructions below when performing operations.
ER (RMT-NWS10B) OR THE REMOTE COMMANDER
(RMT-NWS10B) LITHIUM BATTERY
For the remote commander (RMT-NWS10B) lithium battery, be
sure to follow the instructions below when performing operations.
When Replacing the Remote Commander
(RMT-NWS10B)
Procedure:
1. Remove the four screws on the bottom of the new remote com-
(RMT-NWS10B)
Procedure:
1. Remove the four screws on the bottom of the new remote com-
mander (RMT-NWS10B), and remove the rear cover.
2. Remove the lithium battery.
3. Put a mark on the new lithium battery. (Refer to “Marking the
3. Put a mark on the new lithium battery. (Refer to “Marking the
lithium battery” below.)
4. Following “Attaching the rear cover” below, install the marked
lithium battery in the remote commander (RMT-NWS10B) in
step 1.
step 1.
5. Deliver the remote commander (RMT-NWS10B) for which
the above procedure has been completed to the customer.
When Replacing Only the Lithium Battery
Procedure:
1. Remove the four screws on the bottom of the customer’s re-
Procedure:
1. Remove the four screws on the bottom of the customer’s re-
mote commander (RMT-NWS10B), and remove the rear cov-
er.
er.
2. Remove the lithium battery.
3. Put a mark on the new lithium battery. (Refer to “Marking the
3. Put a mark on the new lithium battery. (Refer to “Marking the
lithium battery” below.)
4. Following “Attaching the rear cover” below, install the marked
lithium battery in the remote commander (RMT-NWS10B) in
step 1.
step 1.
5. Deliver the remote commander (RMT-NWS10B) for which
the above procedure has been completed to the customer.
•
Marking the lithium battery
When installing the lithium battery in the RMT-NWS10B or re-
placing the lithium battery, be sure to follow the instructions be-
low, and place a mark on the lithium battery with a blue marker
pen.
placing the lithium battery, be sure to follow the instructions be-
low, and place a mark on the lithium battery with a blue marker
pen.
Note 1: Do not use a black marker pen.
Marker Pen (Recommended):
PILOT Twin Marker (Blue)
PILOT Twin Marker (Blue)
Note 2: The photo is for reference only. The actual marker pen may be
different.
Mark location:
Using a blue marker pen, put a dot
in the area marked with a dotted line.
Note 3: Do not place the mark on an
engraved
in the area marked with a dotted line.
Note 3: Do not place the mark on an
engraved
area.
Lithium battery
•
Attaching the rear cover
Since the RMT-NWS10B is waterproof, be sure to attach the rear
cover following the procedure below.
Procedure:
1. Install the packing in the groove.
cover following the procedure below.
Procedure:
1. Install the packing in the groove.
Note 4: Install the packing so that none of it is hanging out of the groove.
(Refer to the fi gure below.)
Note 5: Be sure that there is nothing between the packing and the groove,
such as dirt or dust.
packing
groove
Remote commander bottom side
Not inside
the groove.
the groove.
OK
NG
2. Install the marked lithium battery with the SONY logo facing
up.
lithium battery (marked)
3. Install the rear cover.
rear cover
4. Install the screws in the order shown in the fi gure below.
Note 6: Install the screws in the order shown in the fi gure below.
Torque value: 0.10 ± 0.005 N • m
1
2
3
4
screws (four pieces)
Click on the first or last page to see other NWZ-WS613 / NWZ-WS615 service manuals if exist.