Read Sony NW-E013 / NW-E013F / NW-E015 / NW-E015F / NW-E016 / NW-E016F Service Manual online
13
NW-E013/E013F/E015/E015F/E016/E016F
SECTION 4
TEST MODE
1. HOW TO ENTER THE TEST MODE
1. While holding the u button, press the following buttons
one after another in the order shown below.
VOL+
VOL+
t VOL+ t VOL– t VOL– t VOL+ t
VOL–
t VOL+ t VOL– t
HOME
t
HOME
2. After the screen turns off once and turns back on, remove your
hand from the u button.
3. Wait until the message “PUSH ANY KEY GOTO MENU...”
is displayed on the screen.
4. When any button is pressed, the main menu appears.
“*** MAIN MENU ***”
“1. KEY CHECK”
“1. KEY CHECK”
2. HOW TO CHANGE THE TEST MODE
1. Enter the TEST mode so that the MAIN MENU is displayed
on the screen.
2. Select the desired test item by using the > button and the
. button.
3. Click the u button to display the SUB MENU of the
selected test item.
4. Press and hold the u button until “RETURN” is displayed
on the screen to return the screen from the SUB MENU to the
MAIN MENU.
MAIN MENU.
3. SYSTEM PARAMETER INITIALIZE
1. While the MAIN MENU is displayed in the TEST mode, select
“4. SYSTEM” by using the > button and the . button.
2. Click the u button to display “1. SYSTEM PARAM INIT”
of the SYSTEM menu.
3. Click the u button to display the following message:
“PUSH ‘PLAY’ START”
4. Click the u button. Then, the system parameters are all
initialized. Upon completion of the parameter initialization,
the screen displays the following message and returns to the
SYSTEM menu.
the screen displays the following message and returns to the
SYSTEM menu.
“Parameter Initialized.”
4. ALL KEY CHECK MODE
1. Set the HOLD B switch to the HOLD ON position.
2. While the MAIN MENU is displayed in the TEST mode, select
2. While the MAIN MENU is displayed in the TEST mode, select
“1. KEY CHECK” by using the > button and the .
button.
button.
3. Click the u button to display “1. DEVICE CHECK” of the
KEY CHECK menu.
4. Click the u button to display the following message:
“PUSH ‘ANY KEY’ START”
5. Press the u button to display the following message:
“0x0001 (ALL=0x01f7)
6. Press the
HOME button to add the hexadecimal
number 2h and display the following indication:
“0x0003 (ALL=0x01f7)
7. Set the HOLD B switch in the HOLD OFF position to add
the hexadecimal number 4h and display the following
indication:
indication:
“0x0007 (ALL=0x01f7)
8. Press the VOL– button to add the hexadecimal number 10h
and display the following indication:
“0x0017 (ALL=0x01f7)
9. Press the VOL+ button to add the hexadecimal number 20h
and display the following indication:
“0x0037 (ALL=0x01f7)
10. Press the > button to add the hexadecimal number 40h
and display the following indication:
“0x0077 (ALL=0x01f7)
11. Press the . button to add the hexadecimal number 80h
and display the following indication:
“0x00f7 (ALL=0x01f7)
12. Press the PLAY MODE/SOUND button to return the screen
to the SUB MENU “1. DEVICE CHECK” after displaying
“KEY CHECK OK”.
“KEY CHECK OK”.
13. While the screen is in any step of step 5 to 11 of the All Key
Check Mode, press and hold the u button until “RETURN”
is displayed on the screen to cancel the All Key Check Mode
and return to the KEY CHECK menu.
is displayed on the screen to cancel the All Key Check Mode
and return to the KEY CHECK menu.
5. CHARGE CURRENT SELECT
1. While the MAIN MENU is displayed in the TEST mode, select
“2. CHARGE” by using the > button and the . button.
2. Click the u button to display “1. CHARGE START/STOP”
of the CHARGE menu.
3. Select “2. SET CHARGE POWER” by the > button.
4. Whenever the u button is clicked, the charge current toggles
4. Whenever the u button is clicked, the charge current toggles
between the two values as shown.
“CHG: 100mA” and “CHG: 500mA”
5. Press and hold the u button until “RETURN” is displayed
on the screen and return to the CHARGE menu.
6. CHARGE ON/OFF SELECT
1. Connect the equipment to the USB port of a PC.
2. While the MAIN MENU is displayed in the TEST mode, select
2. While the MAIN MENU is displayed in the TEST mode, select
“2. CHARGE” by using the > button and the . button.
3. Click the u button to display “1. CHARGE START/STOP”
of the CHARGE menu.
4. Click the u button to display the following message:
“CHG: XXXmA”
“CHG: STOP” (or “CHG: START”)
“CHG: STOP” (or “CHG: START”)
5. Whenever the u button is clicked, the charge current is
turned ON and OFF, and the screen toggles between the
following two messages.
following two messages.
“CHG: XXXmA”
“ CHG: START
“ CHG: START
t Started.”
And
“CHG: XXXmA”
“CHG: STOP
“CHG: XXXmA”
“CHG: STOP
t Stopped.”
6. Press and hold the u button until “RETURN” is displayed
to return to the CHARGE menu.
7. BEEP ON/OFF
1. While the MAIN MENU is displayed in the TEST mode, select
“5. BEEP” by using the > button and the . button.
2. Click the u button to display “1. BEEP ON/OFF” of the
BEEP menu.
3. Whenever the u button, the screen toggles between the
following two messages:
“BEEP ON” and “BEEP OFF”
4. Confirm that the beep sounds from the headphones when
“BEEP OFF” is switched to “BEEP ON”.
5. Press and hold the u button until “RETURN” is displayed
on the screen to return to the BEEP menu.
Click on the first or last page to see other NW-E013 / NW-E013F / NW-E015 / NW-E015F / NW-E016 / NW-E016F service manuals if exist.