Read Sony MHC-V515 Service Manual online
MICROFILM
SERVICE MANUAL
MINI Hi-Fi COMPONENT SYSTEM
E Model
Chinese Model
SPECIFICATIONS
HCD-V515
Dolby noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol
from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol
a
are trade-
marks of Dolby Laboratories Licensing Corporation.
HCD-V515 is the Amplifier, Video CD
player, Tape Deck and Tuner section in
MHC-V515.
player, Tape Deck and Tuner section in
MHC-V515.
– Continued on next page –
• HCD-V515 is almost same as HCD-V717.
This manual contains only the points which differ
from HCD-V717.
Please refer to HCD-V717 service manual (9-922-879-
from HCD-V717.
Please refer to HCD-V717 service manual (9-922-879-
∏
)
previously issued for other information.
– 2 –
– 3 –
TABLE OF CONTENTS
1.
SERVICING NOTES
...............................................
3
2.
GENERAL
Location of Controls .......................................................
5
Setting the Time ..............................................................
6
3.
DIAGRAMS
3-1. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
8
3-2. Printed Wiring Board – MAIN Section – ......................
9
3-3. Schematic Diagram – MAIN Section (1/4) – ............... 11
3-4. Schematic Diagram – MAIN Section (2/4) – ................ 13
3-5. Schematic Diagram – MAIN Section (3/4) – ................ 15
3-6. Schematic Diagram – MAIN Section (4/4) – ................ 17
3-7. Printed Wiring Board – PANEL Section – .................... 19
3-8. Schematic Diagram – PANEL Section – ....................... 21
3-9. Printed Wiring Board – POWER AMP Section – ......... 24
3-10. Schematic Diagram – POWER AMP Section – ............ 25
3-11. Printed Wiring Board
3-4. Schematic Diagram – MAIN Section (2/4) – ................ 13
3-5. Schematic Diagram – MAIN Section (3/4) – ................ 15
3-6. Schematic Diagram – MAIN Section (4/4) – ................ 17
3-7. Printed Wiring Board – PANEL Section – .................... 19
3-8. Schematic Diagram – PANEL Section – ....................... 21
3-9. Printed Wiring Board – POWER AMP Section – ......... 24
3-10. Schematic Diagram – POWER AMP Section – ............ 25
3-11. Printed Wiring Board
– TRANSFORMER Section – ........................................ 27
3-12. Schematic Diagram
– TRANSFORMER Section – ........................................ 28
4.
EXPLODED VIEWS
................................................ 29
5.
ELECTRICAL PARTS LIST
............................... 33
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
The following caution label is located inside the unit.
– 4 –
MODEL IDENTIFICATION
– Back Panel –
– Back Panel –
PART No.
MODEL
PART No.
Malaysia and Singapore models
4-999-906-0
π
Saudi Arabia model
4-999-906-1
π
Chinese model
4-999-906-2
π
Hong Kong model
4-999-906-3
π
Taiwan model
4-999-906-4
π
Indonesia model
4-999-906-5
π
Thai model
4-999-906-9
π
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
!
OR DOTTED
LINE WITH MARK
!
ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.
IC502 OF VIDEO BOARD
IC502 of the VIDEO board consists of the former type and new
type. The following table shows the differences between the two
types.
Only spare parts for the new type IC502 are supplied.
Units using the former IC502 will not function when replaced with
the new type without performing the following procedure.
Consequently, replace IC502 of units using the former type ac-
cording to the following procedure.
type. The following table shows the differences between the two
types.
Only spare parts for the new type IC502 are supplied.
Units using the former IC502 will not function when replaced with
the new type without performing the following procedure.
Consequently, replace IC502 of units using the former type ac-
cording to the following procedure.
Table of Differences
Replacing Procedure
1. Remove IC402.
2. Solder JW421 and JW422, or short-circuit with a lead wire,
2. Solder JW421 and JW422, or short-circuit with a lead wire,
etc.
3. Replace IC502 with a new one.
How to Differentiate
[VIDEO board] (Side A)
FORMER TYPE
NEW TYPE
C407, 408
MOUNT
NO MOUNT
IC502
M30620MC-302FP
M30620MC-305FP
JW421, JW422
NO MOUNT
MOUNT
IC402
MOUNT
NO MOUNT
R413, 421, 422
MOUNT
NO MOUNT
X401
MOUNT
NO MOUNT
Those with IC402
: FORMER TYPE
Those without IC402: NEW TYPE
