Read Sony MDS-SD1 Service Manual online
– 21 –
“CPLAY MID”
n “CPLAY OUT” n “CPLAY IN”
“CPLAY MID”
n “CPLAY OUT” n “CPLAY IN”
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
2 Rotate the – ˜ + knob and display “CPLAY MODE”.
2 Rotate the – ˜ + knob and display “CPLAY MODE”.
3 Press the ENTER/YES button to change the display to “CPLAY MID”.
4 When access completes, the display changes to “C1 =
4 When access completes, the display changes to “C1 =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
1 Press the ENTER/YES button during continuous playback to change the display as below.
When pressed another time, the parts to be played back can be moved.
2 When access completes, the display changes to “C1 =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
1 Press the MENU/NO button. The display will change to “CPLAY MODE”.
2 Press the § button to remove the disc.
Note : The playback start addresses for IN, MID, and OUT are as follows.
2 Press the § button to remove the disc.
Note : The playback start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID 300h cluster
OUT 700h cluster
OUT 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)
1. Entering the continuous recording mode
1 Set a recordable disc in the unit.
2 Rotate the – ˜ + knob and display “CREC MODE”.
2 Rotate the – ˜ + knob and display “CREC MODE”.
3 Press the ENTER/YES button to change the display to “CREC MID”.
4 When access completes, the display changes to “CREC (
4 When access completes, the display changes to “CREC (
” and
REC
lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
1 When the ENTER/YES button is pressed during continuous recording, the display changes as below.
When pressed another time, the parts to be recorded can be changed.
REC
goes off.
2 When access completes, the display changes to “CREC (
)” and
REC
lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
1 Press the MENU/NO button. The display changes to “CREC MODE” and
REC
goes off.
2 Press the § button to remove the disc.
Note 1 : The recording start addresses for IN, MID, and OUT are as follows.
Note 1 : The recording start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID
300h cluster
OUT
700h cluster
Note 2 : The MENU/NO button can be used to stop recording anytime.
Note 3 : Do not perform continuous recording for long periods of time above 5 minutes.
Note 4 : During continuous recording, be careful not to apply vibration.
Note 3 : Do not perform continuous recording for long periods of time above 5 minutes.
Note 4 : During continuous recording, be careful not to apply vibration.
4-5-3. Non-Volatile Memory Mode (EEP MODE)
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If set accidentally, press the MENU/NO button immediately to exit it.
It is not used in servicing. If set accidentally, press the MENU/NO button immediately to exit it.
4-6. FUNCTIONS OF OTHER BUTTONS
¢
Contents
Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking servo turns
ON/OFF.
Stops continuous playback and continuous recording.
The sled moves to the outer circumference only when this is pressed.
The sled moves to the inner circumference only when this is pressed.
Switches between the pit and groove modes when pressed.
Switches the displayed contents each time the button is pressed
Ejects the disc
Exits the test mode
Function
π
)/±
0/≠
SCROLL
DISPLAY
§
1/u
Click on the first or last page to see other MDS-SD1 service manuals if exist.