Read Sony MDS-JE520 Service Manual online
– 7 –
LASER POWER METER
When performing laser power checks and adjustment (electrical adjustment), use of the new MD laser power meter 8010S (J-2501-145-A)
instead of the conventional laser power meter is convenient.
It sharply reduces the time and trouble to set the laser power meter sensor onto the objective lens of the pick-up.
instead of the conventional laser power meter is convenient.
It sharply reduces the time and trouble to set the laser power meter sensor onto the objective lens of the pick-up.
External View of MD Laser Power Meter 8010S
IOP DATA RECORDING AND DISPLAY WHEN PICKUP AND NON-VOLATILE MEMORY (IC171 OF BD BOARD)
ARE REPLACED
ARE REPLACED
The IOP value labeled on the pick-up can be recorded in the non-volatile memory. By recording the value, it will eliminate the need to look
at the value on the label of the optical pick-up. When replacing the pick-up or non-volatile memory (IC171 of BD board), record the IOP
value on the pick-up according to the following procedure.
at the value on the label of the optical pick-up. When replacing the pick-up or non-volatile memory (IC171 of BD board), record the IOP
value on the pick-up according to the following procedure.
Record Precedure:
1. While pressing the AMS knob and p button, connect the power plug to the outlet, and release the AMS knob and p button.
2. Rotate the AMS knob to display “[Service]”, and press the YES button.
3. Rotate the AMS knob to display “lop.Write” (C28), and press the YES button.
4. The display becomes “Ref=@@@.@” (@ is an arbitrary number) and the numbers which can be changed will blink.
5. Input the IOP value written on the optical pick-up.
1. While pressing the AMS knob and p button, connect the power plug to the outlet, and release the AMS knob and p button.
2. Rotate the AMS knob to display “[Service]”, and press the YES button.
3. Rotate the AMS knob to display “lop.Write” (C28), and press the YES button.
4. The display becomes “Ref=@@@.@” (@ is an arbitrary number) and the numbers which can be changed will blink.
5. Input the IOP value written on the optical pick-up.
To select the number : Rotate the AMS knob.
To select the digit
To select the digit
: Press the AMS knob.
6. When the YES button is pressed, the display becomes “Measu=@@@.@” (@ is an arbitrary number).
7. As the adjustment results are recorded for the 6 value. Leave it as it is and press the YES button.
8. “Complete!” will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become “Iop
7. As the adjustment results are recorded for the 6 value. Leave it as it is and press the YES button.
8. “Complete!” will be displayed momentarily. The value will be recorded in the non-volatile memory and the display will become “Iop
Write”.
9. Press the REPEAT button to complete. “Standby” will be displayed.
Display Precedure:
1. While pressing the AMS knob and p button, connect the power plug to the outlet, and release the AMS knob and p button.
2. Rotate the AMS knob to display “[Service]”, and press the YES button.
3. Rotate the AMS knob to display “lop.Read” (C27).
4. “@@.@/##.#” is displayed and the recorded contents are displayed.
1. While pressing the AMS knob and p button, connect the power plug to the outlet, and release the AMS knob and p button.
2. Rotate the AMS knob to display “[Service]”, and press the YES button.
3. Rotate the AMS knob to display “lop.Read” (C27).
4. “@@.@/##.#” is displayed and the recorded contents are displayed.
@@.@ : indicates the Iop value labeled on the pick-up.
##.#
##.#
: indicates the Iop value after adjustment
5. To end, press the AMS button or MENU/NO button to display “Iop Read”. Then press the REPEAT button to display “Standby”.
Click on the first or last page to see other MDS-JE520 service manuals if exist.