Read Sony MDS-JE320 Service Manual online
— 14 —
4
4
4-5-1. Operating the Continuous Playback Mode
1.
Entering the continuous playback mode
1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
2 Rotate the AMS knob and display “CPLAY MODE”.
3 Press the YES button to change the display to “CPLAY MID”.
4 When access completes, the display changes to “C1 =
2 Rotate the AMS knob and display “CPLAY MODE”.
3 Press the YES button to change the display to “CPLAY MID”.
4 When access completes, the display changes to “C1 =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
2.
Changing the parts to be played back
1 Press the YES button during continuous playback to change the display as below.
“CPLAY MID”
n “CPLAY OUT”n “CPLAY IN”
When pressed another time, the parts to be played back can be moved.
2 When access completes, the display changes to “C1 =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
3.
Ending the continuous playback mode
1 Press the EDIT/NO button. The display will change to “CPLAY MODE”.
2 Press the §EJECT button to remove the disc.
2 Press the §EJECT button to remove the disc.
Note : The playback start addresses for IN, MID, and OUT are as follows. In case you want to display the address of the playback position
on the display, press the DISPLAY/CHAR button and display “CPLAY (
)”.
IN
40h cluster
MID 300h cluster
OUT 700h cluster
OUT 700h cluster
4-5-2.
Operating the Continuous Recording Mode
1.
Entering the continuous recording mode
1 Set a recordable disc in the unit. (Refer to Note 3)
2 Rotate the AMS knob and display “CREC MODE”.
3 Press the YES button to change the display to “CREC MID”.
4 When access completes, the display changes to “CREC (
2 Rotate the AMS knob and display “CREC MODE”.
3 Press the YES button to change the display to “CREC MID”.
4 When access completes, the display changes to “CREC (
)” and
REC
lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
2.
Changing the parts to be recorded
1 When the YES button is pressed during continuous recording, the display changes as below.
“CPLAY MID”
n “CPLAY OUT”n “CPLAY IN”
When pressed another time, the parts to be recorded can be changed.
REC
goes off.
2 When access completes, the display changes to “CREC (
)” and
REC
lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
3.
Ending the continuous recording mode
1 Press the EDIT/NO button. The display changes to “CREC MODE” and
REC
goes off.
2 Press the §EJECT button to remove the disc.
Note 1 : The recording start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID
300h cluster
OUT
700h cluster
Note 2 : The EDIT/NO button can be used to stop recording anytime.
Note 3 : During the test mode, the erasing-protection tab will not be detected. Therefore be careful not to set the continuous recording
Note 3 : During the test mode, the erasing-protection tab will not be detected. Therefore be careful not to set the continuous recording
mode when a disc not to be erased is set in the unit.
Note 4 : Do not perform continuous recording for long periods of time above 5 minutes.
Note 5 : During continuous recording, be careful not to apply vibration.
Note 5 : During continuous recording, be careful not to apply vibration.
4-5-3. Non-Volatile Memory Mode
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If set accidentally, press the EDIT/NO button immediately to exit it.
It is not used in servicing. If set accidentally, press the EDIT/NO button immediately to exit it.
Click on the first or last page to see other MDS-JE320 service manuals if exist.