Read Sony MDS-JA50ES Service Manual online
— 3 —
This appliance is classified as a CLASS 1
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.
The following caution label is located
inside the unit.
inside the unit.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
other than those specified herein may result in hazardous ra-
diation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
The laser component in this product is
capable of emitting radiation exceeding
the limit for Class 1.
capable of emitting radiation exceeding
the limit for Class 1.
MODEL IDENTIFICATION
— BACK PANEL —
— BACK PANEL —
Parts No.
4-987-511-2
: AEP, UK, German model
4-987-511-3
: US model
TABLE OF CONTENTS
1. SERVICING NOTE
.......................................................... 4
2. GENERAL
.......................................................................... 7
3. DISASSEMBLY
3-1. Tray Assembly .................................................................... 26
3-2. Bracket (Motor) ASSY ....................................................... 27
3-3. Holder ASSY ...................................................................... 27
3-4. Base Unit ............................................................................. 28
3-5. HMOT Board and HLIM Board ......................................... 28
3-2. Bracket (Motor) ASSY ....................................................... 27
3-3. Holder ASSY ...................................................................... 27
3-4. Base Unit ............................................................................. 28
3-5. HMOT Board and HLIM Board ......................................... 28
4. TEST MODE
..................................................................... 29
5. ELECTRICAL ADJUSTMENTS
............................... 32
6. DIAGRAMS
6-1. Brock Diagrams
• BD Section ....................................................................... 37
• Digital Section ................................................................. 39
• Audio Section .................................................................. 41
• Power Section .................................................................. 43
• Digital Section ................................................................. 39
• Audio Section .................................................................. 41
• Power Section .................................................................. 43
6-2. Circuit Boards Location ...................................................... 44
6-3. Waveforms ......................................................................... 45
6-4. Printed Wiring Board — BD Section — ............................. 47
6-5. Schematic Diagram — BD Section — ............................... 49
6-6. Schematic Diagram — Digital Section — .......................... 52
6-7. Printed Wiring Board — Digital Section — ....................... 55
6-8. Printed Wiring Board — MD Section — ............................ 57
6-9. Schematic Diagram — MD Section — .............................. 58
6-10. Printed Wiring Board — D Out, D Vol Section — .......... 59
6-11. Schematic Diagram — D Out, D Vol Section — ............. 60
6-12. Printed Wiring Board — DA Section — .......................... 61
6-13. Schematic Diagram — DA Section — ............................. 63
6-14. Printed Wiring Board — AD Section — .......................... 65
6-15. Schematic Diagram — AD Section — ............................. 67
6-16. Printed Wiring Board — Panel Section — ....................... 69
6-17. Schematic Diagram — Panal Section — ......................... 71
6-18. Printed Wiring Board — Power Section — ..................... 73
6-19. Schematic Diagram — Power Section — ........................ 75
6-20. IC Block Diagrams ........................................................... 77
6-21. IC Pin Functions ............................................................... 84
6-3. Waveforms ......................................................................... 45
6-4. Printed Wiring Board — BD Section — ............................. 47
6-5. Schematic Diagram — BD Section — ............................... 49
6-6. Schematic Diagram — Digital Section — .......................... 52
6-7. Printed Wiring Board — Digital Section — ....................... 55
6-8. Printed Wiring Board — MD Section — ............................ 57
6-9. Schematic Diagram — MD Section — .............................. 58
6-10. Printed Wiring Board — D Out, D Vol Section — .......... 59
6-11. Schematic Diagram — D Out, D Vol Section — ............. 60
6-12. Printed Wiring Board — DA Section — .......................... 61
6-13. Schematic Diagram — DA Section — ............................. 63
6-14. Printed Wiring Board — AD Section — .......................... 65
6-15. Schematic Diagram — AD Section — ............................. 67
6-16. Printed Wiring Board — Panel Section — ....................... 69
6-17. Schematic Diagram — Panal Section — ......................... 71
6-18. Printed Wiring Board — Power Section — ..................... 73
6-19. Schematic Diagram — Power Section — ........................ 75
6-20. IC Block Diagrams ........................................................... 77
6-21. IC Pin Functions ............................................................... 84
7. EXPLODED VIEWS
7-1. Main Section ..................................................................... 100
7-2. Chassis Section ................................................................. 101
7-3. Front Panel Section 1 ........................................................ 102
7-4. Front Panel Section 2 ........................................................ 103
7-5. Mechanism Section 1 (MDM-4A) .................................... 104
7-6. Mechanism Section 2 (MDM-4A) .................................... 105
7-7. Mechanism Section 3 (MDM-4A) .................................... 106
7-8. Base Unit Section (MBU-2B) ........................................... 107
7-2. Chassis Section ................................................................. 101
7-3. Front Panel Section 1 ........................................................ 102
7-4. Front Panel Section 2 ........................................................ 103
7-5. Mechanism Section 1 (MDM-4A) .................................... 104
7-6. Mechanism Section 2 (MDM-4A) .................................... 105
7-7. Mechanism Section 3 (MDM-4A) .................................... 106
7-8. Base Unit Section (MBU-2B) ........................................... 107
8. ELECTRICAL PARTS LIST
...................................... 108
Click on the first or last page to see other MDS-JA50ES service manuals if exist.