Read Sony ICF-CDK70 Service Manual online
ICF-CDK70
4
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Features
3-CD changer
CD-R/RW playback function
Bass Reflex sound system
FM/AM Digital Tuner with 30 station presets
Audio In jack for digital music player connectivity
Easy-to-set countdown timer for cooking
Digital music player holder and cable (supplied)
Magnetic remote commander (supplied)
CD-R/RW playback function
Bass Reflex sound system
FM/AM Digital Tuner with 30 station presets
Audio In jack for digital music player connectivity
Easy-to-set countdown timer for cooking
Digital music player holder and cable (supplied)
Magnetic remote commander (supplied)
Installing the Unit Under a
Cabinet
Cabinet
(See Fig.
)
Caution
Please read the following before
installing the unit
installing the unit
Due to its heavy weight, the unit should be installed
with great care.
Installation of the unit requires two persons.
Use tools carefully while installing of the unit.
Be sure that the cabinet that is used is sturdy enough
to support the weight of the unit.
To reduce the risk of fire, do not place any heating or
cooking appliance beneath this unit.
Install the unit so that its AC power cord can be
connected directly to a wall outlet. Do not use a
converter or extension cord.
Be sure that the AC power cord has no slack during
use of the unit, since the cord acts as an FM wire
antenna. If the AC power cord has some slack, wind
it around the cord hook so as to eliminate the slack.
The unit has a built-in ferrite bar antenna for AM
radio reception. Confirm that AM reception is
acceptable before finally attaching the unit.
Install the unit as far as possible from sources of
noise (for example, a refrigerator, microwave oven or
fluorescent lamp).
This unit is not waterproof. Install it where it will
not be exposed to splashing by water, as this may
damage the unit.
To reduce the risk of fire or electric shock, do not
touch the AC power cord with wet hands.
Never place objects between the top of the unit and
the bottom of the cabinet. This could cause the unit
to fall.
Make sure the unit’s four screws are fastened tightly.
After installing the unit, do not pull down on it or
hang something heavy on it.
with great care.
Installation of the unit requires two persons.
Use tools carefully while installing of the unit.
Be sure that the cabinet that is used is sturdy enough
to support the weight of the unit.
To reduce the risk of fire, do not place any heating or
cooking appliance beneath this unit.
Install the unit so that its AC power cord can be
connected directly to a wall outlet. Do not use a
converter or extension cord.
Be sure that the AC power cord has no slack during
use of the unit, since the cord acts as an FM wire
antenna. If the AC power cord has some slack, wind
it around the cord hook so as to eliminate the slack.
The unit has a built-in ferrite bar antenna for AM
radio reception. Confirm that AM reception is
acceptable before finally attaching the unit.
Install the unit as far as possible from sources of
noise (for example, a refrigerator, microwave oven or
fluorescent lamp).
This unit is not waterproof. Install it where it will
not be exposed to splashing by water, as this may
damage the unit.
To reduce the risk of fire or electric shock, do not
touch the AC power cord with wet hands.
Never place objects between the top of the unit and
the bottom of the cabinet. This could cause the unit
to fall.
Make sure the unit’s four screws are fastened tightly.
After installing the unit, do not pull down on it or
hang something heavy on it.
1
Decide on the installation location and
orientation of the unit based on the best
reception that is possible (see “Improving
the Reception”).
orientation of the unit based on the best
reception that is possible (see “Improving
the Reception”).
2
Mark the position of the 4 holes by using
the supplied template. Use a drill to make
the holes (size 6.5 mm diam.,
the supplied template. Use a drill to make
the holes (size 6.5 mm diam.,
9
/
32
inch). (See
Fig.
-)
3
When the cabinet door overhangs the shelf
and obstructs the unit, you can adjust the
unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you
can adjust the height in 4 steps (H
and obstructs the unit, you can adjust the
unit/shelf height.
First set the L mark to the dot which
becomes the lowest position, then you
can adjust the height in 4 steps (H
L)
by turning the spacer counterclockwise
(See Fig.
(See Fig.
-). The unit can be installed
without the spacer.
4
Install the unit with the supplied mounting
screws. (See Fig.
screws. (See Fig.
-)
Note
If you lose the supplied screws, please purchase #10 or
M5 screws.
If you lose the supplied screws, please purchase #10 or
M5 screws.
Installing the Batteries
into the Remote
Commander
into the Remote
Commander
(See Fig.
-
)
Insert two size AAA (R03) batteries (not supplied).
When to replace the batteries
With normal use, the batteries should last for about
six months. When the remote no longer operates the
CD kitchen clock radio, replace all the batteries with
new ones.
six months. When the remote no longer operates the
CD kitchen clock radio, replace all the batteries with
new ones.
Notes
Do not charge the dry batteries.
If you do not intend to use the remote for a long
time, remove the batteries to prevent damage by
leakage and corrosion.
If you do not intend to use the remote for a long
time, remove the batteries to prevent damage by
leakage and corrosion.
Use of Magnet (See Fig.
-
)
A magnet is provided on the back of the remote so
that it can be attached a refrigerator or other iron
surface.
However, do not operate the remote while it is
attached in this manner.
that it can be attached a refrigerator or other iron
surface.
However, do not operate the remote while it is
attached in this manner.
Note
Do not place the remote commander near magnetic
cards such as credit cards.
Do not place the remote commander near magnetic
cards such as credit cards.
Setting the Clock
1
Plug in the unit.
“AM 12:00” flashes in the display.
2
Hold down CLOCK/D.S.T until a short beep
sounds.
sounds.
The hour starts to flash in the display.
3
Turn the TIMER jog dial towards + or
– repeatedly until the correct hour appears
in the display.
– repeatedly until the correct hour appears
in the display.
4
Press TIMER once.
The minute flashes.
5
Repeat steps 3 and 4 to set the minute, and
press TIMER.
press TIMER.
Two short beeps sound and the seconds start
incrementing from zero.
incrementing from zero.
12-hour system: “AM 12:00” = midnight
In step 4 and 5, you can press CLOCK/D.S.T instead
of TIMER.
In step 4 and 5, you can press CLOCK/D.S.T instead
of TIMER.
To the display to summer time
(daylight saving time)
(daylight saving time)
Press CLOCK/D.S.T.
“ ” is displayed and the time indication changes to
summer time.
To deactivate the summer time function, press
CLOCK/D.S.T again.
“ ” is displayed and the time indication changes to
summer time.
To deactivate the summer time function, press
CLOCK/D.S.T again.
H
L
AC power cord
Cord clamp
Template
Spacer
L (Low)
Dot
Mounting screw
CD
button have a tactile dot.
There is a tactile dot
next to VOLUME +.
next to VOLUME +.
Turn
Push
TIMER indicator
Size AAA
(R03)
(R03)
2
The number 5 and the VOL +
buttons have a tactile dot.
buttons have a tactile dot.
Magnet
Click on the first or last page to see other ICF-CDK70 service manuals if exist.