ICF-CD853V - Sony Audio Service Manual (repair manual)

icf-cd853v service manual
Model
ICF-CD853V
Pages
39
Size
2.4 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
icf-cd853v.pdf
Date

Read Sony ICF-CD853V Service Manual online

SERVICE MANUAL
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 4–ohm loads, both channels driven from
100 – 10 000 Hz; rated 1.0 W per channel-
minimum RMS power, with no more than 10 %
total harmonic distortion in AC operation.
CD player section
System: Compact disc digital audio system
Laser diode properties:  Material: GaAlAs
Wavelength: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 
µ
W
(This output is the value measured at a
distance of about 200 mm from the objective
lens surface on the optical pick-up block with
7 mm aperture.)
Frequency response: 20-20 000 Hz 
 +1
–1.5
 dB
Wow and flutter: Below measurable limit
Radio section
Frequency range:
TV:
2 – 13 ch
WEATHER: 1 – 7 ch
FM:
87.5 – 108 MHz
AM:
530 – 1 710 kHz
General
Time display: 12-hour system
Speaker: 66 mm (2 
5
/
8
 
inches) dia., 4 
Outputs: i (headphones) jack (ø 3.5 mm
stereo minijack)
Power outputs:
1.2W + 1.2W (at 10% harmonic distortion)
Power requirements: 120 V AC, 60 Hz
Dimensions:
Approx. 185.5 
×
 176 
×
 210.5 mm (w/h/d)
(Approx. 7 
3
/
8
  
×
 7 
×
 8 
3
/
8
  inches) incl.
projecting parts and controls
Mass: Approx. 1 780 g (3 lb 15
 
oz)
Design and specifications are subject to change
without notice.
TV/WEATHER/FM/AM CD CLOCK RADIO
US Model
SPECIFICATIONS
ICF-CD853V
Ver 1.1  2002.07
9-873-607-02
Sony Corporation
2002G0500-1
Personal Audio Company
C
 2002.07
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CFD-E75
CD Mechanism Type
KSM-213RDP
Optical Pick-up Name
KSS-213R
2
ICF-CD853V
About CD-Rs/CD-RWs
This unit is compatible with CD-Rs/CD-RWs but
playback capability may vary depending on the
quality of the disc, the recording device and
application software.
TABLE  OF  CONTENTS
1.
SERVICING  NOTES
..............................................
3
2.
GENERAL
..................................................................
4
3.
DISASSEMBLY
3-1. Disassembly Flow ...........................................................
5
3-2. Rear Cabinet Assy ...........................................................
6
3-3. CD Lid .............................................................................
6
3-4. Upper Cabinet Assy ........................................................
7
3-5. MAIN Board ...................................................................
7
3-6. CD Block .........................................................................
8
3-7. Optical Pick-up Device (KSS-213R) ..............................
8
4.
ELECTRICAL  ADJUSTMENTS
Tuner Section .................................................................
9
CD Section .....................................................................  11
5.
DIAGRAMS
5-1. Block Diagram  – CD Section – .................................... 12
5-2. Block Diagram  – MAIN Section – ............................... 13
5-3. Note for Printed Wiring Board and
Schematic Diagrams ....................................................... 14
5-4. Printed Wiring Board  – CD Section – .......................... 16
5-5. Schematic Diagram  – CD Section – ............................. 17
5-6. Printed Wiring Board  – MAIN Section – ..................... 18
5-7. Printed Wiring Boards  – POWER Section – ................ 19
5-8. Schematic Diagram  – MAIN section (1/2) – ............... 20
5-9. Schematic Diagram  – MAIN section (2/2) – ............... 21
5-10. Printed Wiring Boards  – PANEL Section – ................. 22
5-11. Schematic Diagram  – PANEL Section – ...................... 23
5-12. IC Pin Function Description .......................................... 25
6.
EXPLODED  VIEWS
6-1. Cabinet Section ............................................................... 26
6-2. Upper Cabinet Section .................................................... 27
6-3. Front Cabinet Section ..................................................... 28
6-4. Rear Cabinet Section ...................................................... 29
6-5. Optical Block (KSM-213RDP) ....................................... 30
7.
ELECTRICAL  PARTS  LIST
.............................. 31
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  
0
  OR  DOTTED
LINE  WITH  MARK  
0
  ON  THE  SCHEMATIC  DIAGRAMS
AND  IN  THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE
OPERATION.  REPLACE  THESE  COMPONENTS  WITH
SONY  PARTS  WHOSE  PART  NUMBERS  APPEAR  AS
SHOWN  IN  THIS  MANUAL  OR  IN  SUPPLEMENTS  PUB-
LISHED  BY  SONY.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able.  (See Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
0.15 
µ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra-
diation exposure.
3
ICF-CD853V
S302
SECTION  1
SERVICING  NOTES
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES  ON  LASER  DIODE  EMISSION  CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S302. (push switch type)
The following checking method for the laser diode is operable.
• Method
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S302 as shown in Fig.1.
Note:
 Do not push the detection lever strongly, or it may be bent or dam-
aged.
3. Press the
CD 
u
button.
4. Check the object lens for confirming normal emission of the
laser diode. If not emitting, there is a trouble in the automatic
power control circuit or the optical pick-up.
In this operation, the object lens will move up and down 2
times along with inward motion for the focus search.
NOTES  ON  HANDLING  THE  OPTICAL  PICK-UP
BLOCK  OR  BASE  UNIT
CHUCK  PLATE  JIG  ON  REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
Fig.1 Method to push the S302
MODEL  IDENTIFICATION
There are two types of ICF-CD853V.
Please look at the mark of set shown below.
no mark: Original Type
Liv
: Liv Type
– Top View –
4
ICF-CD853V
Setting the Brightness
of the Backlight
Press BRIGHTNESS to select high, middle or low
for the display according to your preferences.
Setting the Clock
and Date
1
Plug in the clock radio.
The display will flash “AM 12:00”.
2
Press CLOCK for a few seconds.
You will hear a beep and the year will start to
flash in the display.
3
Press TUNE/TIME SET + or  until the
correct year appears in the display.
4
Press CLOCK once.
5
Repeat steps 3 and 4 to set the month,
day, hour, and minute.
After setting the minute, press CLOCK to start
the counting of the seconds, and you will
hear two short beeps.
To display the year and date, press
SNOOZE•DATE/SLEEP OFF once for the date,
and within 4 seconds press it again for the year.
The display shows the date or year for a few
seconds and then changes back to the current
time.
To set the current time rapidly, hold down
TUNE/TIME SET + or .
In step 5, when you press CLOCK after the
minute setting to activate the clock, the seconds
start counting from zero.
To change the display to the
daylight saving time (summer time) indication
Press D.S.T./SUMMER T.
” is displayed and the time indication
changes to summer time.
To deactivate the summer time function, press
D.S.T./SUMMER T. again.
FM wire
antenna
AC power
cord
i
(headphones)
jack
The PRESET TUNING 3 button has a
tactile dot.
There is a tactile dot
beside volume to show
the direction to turn up
the volume.
Setting the Alarm
This clock radio is equipped with 3 alarm
modes—CD, radio and buzzer. Before setting the
alarm, make sure to set the clock (see “Setting the
Clock and Date”).
To Set the Alarm Time
To Set the CD Alarm:
For the CD alarm, the track you specified as the
Wake-up track is played first.
(If the CD play mode is set to “SHUFFLE” or
“SHUFFLE REP”, however, all the tracks are
played in random order.)
1
With the alarm turned on, adjust the
volume to the level you require.
2
Press ALARM SET CD for a few
seconds.
“ALARM”, “CD” appear on the display.
After one beep, “ALARM” and the hour will
start to flash in the display.
3
Press TUNE/TIME SET + or  until the
desired hour appears.
To set the hour rapidly, hold down TUNE/
TIME SET +
 or .
4
Press ALARM SET CD.
The minute will flash.
5
Repeat step 3 to set the minute and
press ALARM SET CD.
The wake-up track number flashes on the
display.
6
Press TUNE/TIME SET + or  to select
the desired wake-up track number.
The wake-up track number can be set up to
99.
7
Press ALARM SET CD.
Two short beeps will confirm the setting.
5
Repeat step 3 to set the minute and
press ALARM SET RADIO.
“WAKE UP STA” appears and the preset
number flashes on the display.
6
Press TUNE/TIME SET + or  to select
the wake-up station.
Preset number changes in the order as
follows:
P-
AM P1 to 5
FM1 P1 to 5
FM2 P1 to 5
TV P1 to 5
WEATHER 
    P1 to 5
“P” is the last received station.
You can directly select the desired wake-up
station by pressing RADIO•BAND or the
PRESET TUNING button while the indication
“P–” is not displayed.
7
Press ALARM SET RADIO.
Two short beeps will confirm the setting.
To Set the Buzzer Alarm:
1
Press ALARM SET BUZZER for a few
seconds.
“ALARM” and “BUZZER” appear on the
display.
After one beep, “ALARM” and the hour will
start to flash on the display.
2
Press TUNE/TIME SET + or  until the
desired hour appears.
To set the hour rapidly, hold down TUNE/
TIME SET +
 or .
3
Press ALARM SET BUZZER.
The minute will flash.
4
Repeat step 2 to set the minute and
press ALARM SET BUZZER.
Two short beeps will confirm the setting.
To Set the Alarm Mode
Before setting the alarm mode, be sure to set the
alarm time. (See “To Set the Alarm Time”.)
Repeat the pressing of ALARM MODE to select
the alarm mode you want. Every time you press
ALARM MODE, CD/RADIO/BUZZER indicator
changes in the order as follows:
CD 
RADIO
BUZZER
CD+RADIO
CD+BUZZER
RADIO+BUZZER
CD+RADIO+BUZZER
OFF
The alarm time which plays or sounds next is
displayed.
To Check the Alarm Setting
For ALARM SET CD, pressing once displays the
alarm time, pressing twice displays the wake-up
track number.
For ALARM SET RADIO, pressing once displays
the alarm time, pressing twice displays the wake-
up station.
For ALARM SET BUZZER, pressing once displays
the alarm time.
The display shows the alarm setting for a few
seconds and then returns to the previous display.
Alarm time in CD alarm, radio alarm and buzzer
alarm is set at AM 12:00 when you purchased the
unit.
ALARM ON—
If you set the CD alarm and there is no disc in
the CD player, the buzzer alarm will sound in its
place at the time set.
For the buzzer alarm, the beeping of the alarm
becomes more rapid after every few seconds in
three progressive stages.
When headphones (not supplied) are plugged
into the unit, buzzer alarm through the speakers
and the headphones regardless of the alarm
mode setting. In this case, the unit will not play a
CD or radio.
Note
When CD, radio and buzzer alarms are set for
the same time, the CD alarm takes precedence. If
the CD alarm is not set, the radio alarm takes
precedence.
To Doze for a Few More
Minutes
Press SNOOZE•DATE/SLEEP OFF.
The CD, radio or buzzer alarm turns off but will
be automatically activated again after about 10
minutes.  Every time you press SNOOZE•DATE/
SLEEP OFF
, the snooze time changes as follows:
10 
20
50
60
30
40
The display shows the snooze time for a few
seconds and returns to show the current time.
When you press SNOOZE•DATE/SLEEP OFF
after the current time appeared, the snooze time
starts from 10 minutes again.
The maximum length of the snooze time is 60
minutes.
The CD u button has a tactile dot.
ALARM OFF—
The CD, radio, or buzzer alarm is turned off
automatically after 60 minutes.
To Stop the Alarm
Press OFF x•ALARM RESET to turn off the
alarm.
The alarm will come on again at the same time
the next day.
To Deactive the Alarm
Press ALARM MODE repeatedly until CD/
RADIO/BUZZER indicator go off.
Setting the Sleep
Timer
You can enjoy falling asleep to the CD or the
radio using the built-in sleep timer that turns off
the CD or the radio automatically after a preset
duration.
Press SLEEP during CD or radio play.
You can set the sleep timer to durations of 90,
60,30, or 15 minutes. Every push changes the
display as follows:
off (current time)
90
60
30
15
“SLEEP” will appear in the display when the
duration time is set.
The CD or the radio will play for the time you
set, then shut off.
To turn off the CD or the radio before the preset
time, press SNOOZE•DATE/SLEEP OFF.
NAP indicator
Features
• TV/WEATHER/FM/AM 4 band PLL (phase
locked loop) synthesized clock radio
• Easy preset digital tuning with 25 memory
presets
• Built-in CD player with CD-R/RW playback
function
• Easy to see large Display with small footprint.
• Triple Alarm (Radio, buzzer or CD) with the
extendable snooze function.
• Easy nap timer –one push operation.
• LCD with backlight which has a brightness
control switch.
• D.S.T. (Daylight Saving Time) –Summer time
calculation.
3
Press TUNE/TIME SET + or  until the
desired hour appears.
To set the hour rapidly, hold down TUNE/
TIME SET +
 or .
4
Press ALARM SET RADIO.
The minute will flash.
To Set the Radio Alarm:
For the radio alarm, the station you specified as
the Wake-up station is played.
1
Tune in to a station and adjust the
volume.
2
Press ALARM SET RADIO for a few
seconds.
“ALARM” and “RADIO” appear on the
display.
After one beep, “ALARM” and the hour will
start to flash on the display.
SECTION  2
GENERAL
This section is extracted from
instruction manual.
Page of 39
Display

Download Sony ICF-CD853V Service Manual (Repair Manual)

Here you can read online and download Sony ICF-CD853V Service Manual in PDF. ICF-CD853V service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sony ICF-CD853V Audio. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.