Read Sony ICD-UX512 / ICD-UX512F / ICD-UX513F Service Manual online
ICD-UX512/UX512F/UX513F
10
SECTION 2
TEST MODE
Setting the TEST MODE allows you to perform various checks
and examinations on this set.
and examinations on this set.
Setting the TEST MODE
Turn power to the set. Turn the [DPC] switch ON from the OFF
state while pressing the [
Turn power to the set. Turn the [DPC] switch ON from the OFF
state while pressing the [
x
STOP] button and the [VOL –] button
at the same time.
Exiting the TEST MODE
Unplug the battery.
Unplug the battery.
TEST MODE Menu and Mode Transition under TEST
MODE
The LCD display given below appears when the TEST MODE is
entered.
MODE
The LCD display given below appears when the TEST MODE is
entered.
Welcom To
Athena World
Athena World
ICD-UX512F/E
1.01.02
1.01.02
LCD display
Select an item using the [
.
]/[
>
] keys and determine the se-
lected item using the [
N
ENT] button.
[>]
button
[.]
button
Turn [DPC] switch off.
TEST MODE
End of TEST MODE
Unplug battery.
Turn [DPC] switch on while pressing
[xSTOP] button and [NENT] button
at the same time.
Initial state of test mode
Release [xSTOP] button
and [NENT] button
SERVICE MENU
VERSION
KEY CHECK
AUDIO LOOP
SIN
BEEP
LCD CONT
LCD PATTERN
RTC TEST
BATT A/D
Z LOAD
LOW DET
VBUS
FM TEST
Key Count
SLEEP
Batt Life
CHG LOG
LREC LOG
LREC LOG Clear
MENU INIT
SERVICE MENU
J
j
Return using
[xSTOP]
button
Determine
using
[NENT]
button
k
K
1. VERSION
Check the model number, F/W version and destination of each
module.
Check the model number, F/W version and destination of each
module.
<VERSION>
ICD-UX512F/E
MAINFW:1.01.02
IPL2FW:1.01.02
LSI 4253
ICD-UX512F/E
MAINFW:1.01.02
IPL2FW:1.01.02
LSI 4253
Model number/destination
F/W version
IPL2 version
CPU version
F/W version
IPL2 version
CPU version
LCD display
2. KEY CHECK
Check the operation of each of the buttons and switches and reset
to the factory defaults.
Check the operation of each of the buttons and switches and reset
to the factory defaults.
<KEY CHECK>
KEY: PLAY
REMAIN: 16
KEY: PLAY
REMAIN: 16
Confirmed key name
Count of keys checked
Count of keys checked
LCD display
Target input keys:
[
[
x
STOP], [
>
], [
.
], [
N
ENT],[
z
REC/PAUSE],
[
A-B], [ERASE], [VOL+], [VOL –], [MENU], [ ],
[T-Mark], [
v
], [
V
], [DPC] SW (OFF
tON),
[HOLD/POWER] SW (OFF
tON)
When all the key inputs have been confi rmed, “ACCESS” is dis-
played and the system is initialized. Once the initialization is com-
pleted, the system is restarted.
(The power ON state is held.)
When “ERROR” is displayed, the mode is held. (The system is
not restarted.)
To exit this mode, disconnect power (unplug the battery).
played and the system is initialized. Once the initialization is com-
pleted, the system is restarted.
(The power ON state is held.)
When “ERROR” is displayed, the mode is held. (The system is
not restarted.)
To exit this mode, disconnect power (unplug the battery).
3. AUDIO LOOP
Perform an Audio Loop Back operation.
Perform an Audio Loop Back operation.
<AUDIO LOOP>
MIC: M AGC: OFF
Vol: 10 MIC IN
D H0 D0
VOR: 00003FFF
MIC: M AGC: OFF
Vol: 10 MIC IN
D H0 D0
VOR: 00003FFF
D: DAMP, (A: Codec)
H0: HP-MUTE=L, (H1: H)
D0: DAMP_XSEL=L, (D1: H)
H0: HP-MUTE=L, (H1: H)
D0: DAMP_XSEL=L, (D1: H)
LCD display
Key input settings under this mode of operation
[VOL+]/[VOL –]: Volume up/down
[
[VOL+]/[VOL –]: Volume up/down
[
z
REC/PAUSE]: Microphone sensitivity change
[
.
]: ALC operation (between ON and OFF)
[ERASE]: HP_MUTE forced operation
[
[
A-B]: DAMP_XSEL forced operation
Ver. 1.1
Click on the first or last page to see other ICD-UX512 / ICD-UX512F / ICD-UX513F service manuals if exist.