Read Sony ICD-SX700 / ICD-SX700D / ICD-SX800 / ICD-SX800D / ICD-SX900 Service Manual online
ICD-SX700/SX700D/SX800/SX800D/SX900
2
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Power requirements
Two LR03 (size AAA) alkaline batteries: 3.0 V DC
Two NH-AAA rechargeable batteries: 2.4 V DC
Two LR03 (size AAA) alkaline batteries: 3.0 V DC
Two NH-AAA rechargeable batteries: 2.4 V DC
Operating temperature
5 ˚C - 35 ˚C (41 ˚F - 95 ˚F)
5 ˚C - 35 ˚C (41 ˚F - 95 ˚F)
Dimensions (w/h/d) (not incl.
projecting parts and controls) (JEITA)*
projecting parts and controls) (JEITA)*
5
31.3
× 130.0 × 15.4 mm (1
1/4
× 5
1/8
×
5/8
in.)
Mass (JEITA)*
5
Approx. 52 g (1
7/8
oz) excluding batteries
*
5
Measured value by the standard of JEITA
(Japan Electronics and Information
Technology
Technology
Industries
Association)
Supplied accessories
IC Recorder (1)
Remove
IC Recorder (1)
Remove
the
fi lm on the display window
before you use the IC recorder.
LR03 (size AAA) alkaline batteries (2) (SX700: US, Canadian)
NH-AAA (size AAA) rechargeable batteries (2)
Stereo headphones* (1) (Except AEP)
Wind Screen (1)
USB connecting cable (1)
Application Software, Digital Voice Editor (CD-ROM)
Cradle* (1) (SX700D/SX800D)
Stand (1) (AEP, E, Chinese, Korea, Taiwan)
Carrying pouch (1)
Microphone* (1) (E, Chinese, Korea, Taiwan)
Battery case* (1) (Except SX700: US, Canadian, Latin American)
Operating Instructions
LR03 (size AAA) alkaline batteries (2) (SX700: US, Canadian)
NH-AAA (size AAA) rechargeable batteries (2)
Stereo headphones* (1) (Except AEP)
Wind Screen (1)
USB connecting cable (1)
Application Software, Digital Voice Editor (CD-ROM)
Cradle* (1) (SX700D/SX800D)
Stand (1) (AEP, E, Chinese, Korea, Taiwan)
Carrying pouch (1)
Microphone* (1) (E, Chinese, Korea, Taiwan)
Battery case* (1) (Except SX700: US, Canadian, Latin American)
Operating Instructions
* The stereo headphones, the cradle , the battery case and
the microphone are supplied with some models in some
regions only.
the microphone are supplied with some models in some
regions only.
Design and specifi cations are subject to change without notice.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Click on the first or last page to see other ICD-SX700 / ICD-SX700D / ICD-SX800 / ICD-SX800D / ICD-SX900 service manuals if exist.