Read Sony HT-ST9 Service Manual online
HT-ST9
6
NOTE OF REPLACING THE IC7004, IC7005, IC7007
AND IC7008 ON THE AMP BOARD AND THE COM-
PLETE AMP BOARD
When IC7004, IC7005, IC7007 and IC7008 on the AMP board and
the complete AMP board are replaced, it is necessary to spread the
compound between the AMP board and the heat sink.
Spread the compound referring to the fi gure below.
AND IC7008 ON THE AMP BOARD AND THE COM-
PLETE AMP BOARD
When IC7004, IC7005, IC7007 and IC7008 on the AMP board and
the complete AMP board are replaced, it is necessary to spread the
compound between the AMP board and the heat sink.
Spread the compound referring to the fi gure below.
– AMP Board (Side A) –
IC7008
IC7004
IC7007
IC7005
compound
compound
NOTE OF REPLACING THE COMPLETE MB1406
BOARD OR CARD WLAN/BT COMBO
When the complete MB1406 board or card WLAN/BT combo is
replaced, you must perform the following item.
When the complete MB1406 board or card WLAN/BT combo is
replaced, you must perform the following item.
When replacing the complete MB1406 board:
• NETWORK INFORMATION WRITING AND CHECKING
• NETWORK INFORMATION WRITING AND CHECKING
OF NETWORK/NFC OPERATION (refer to this page)
•
NOTICE OF MAC ADDRESS CHANGE TO CUSTOMERS
(refer to page 8)
(refer to page 8)
• NOTES ON THE WIRELESS CONNECTION (LINK) AF-
TER REPAIRS ARE COMPLETE (refer to page 8)
When replacing the card WLAN/BT combo:
• NETWORK INFORMATION WRITING AND CHECKING
• NETWORK INFORMATION WRITING AND CHECKING
OF NETWORK/NFC OPERATION (refer to this page)
•
NOTICE OF MAC ADDRESS CHANGE TO CUSTOMERS
(refer to page 8)
(refer to page 8)
NETWORK INFORMATION WRITING AND CHECKING
OF NETWORK/NFC OPERATION
When the complete MB1406 board or card WLAN/BT combo are
replaced, execute the below BD service mode. And check the op-
eration of wireless/wired LAN and NFC.
OF NETWORK/NFC OPERATION
When the complete MB1406 board or card WLAN/BT combo are
replaced, execute the below BD service mode. And check the op-
eration of wireless/wired LAN and NFC.
1. Network information writing
Procedure:
1. Connect this unit with TV monitor.
2. Press the [
1. Connect this unit with TV monitor.
2. Press the [
@
/1
] button to turn the power on.
3. Press button in order of the [
x
] → [DISPLAY] → [
X
] → [
V]
on the remote commander.
(Make the interval when each button is pressed within one sec-
ond)
ond)
4. Enter the BD service mode. The OSD menu on TV monitor
can be operated by remote commander.
5. Press the [
v] button on the remote commander to select
“Diag”, and press the [ ] button on the remote commander.
6. Press the [
b] button on the remote commander to select “Wire-
less LAN Test”. (Screen 1)
7. Press the [
v] button on the remote commander to select “[5]
Write P2P address to Registry”.
8. Press the [ ] button on the remote commander, wait until the
display show “Status: Write Successful!” (Screen 2).
9. Press the [BACK] button on the remote commander to return
to category select screen, and press the [
b] button on the re-
mote commander to select “Bluetooth Device Test”. (Screen 3)
10. Press the [ ] button on the remote commander to select “(1)
Bluetooth Enable”.
11. Press the [ ] button on the remote commander, wait until the
display show “Status: Bluetooth Enable Successful!” (Screen
4).
4).
12. Press the [
v] button on the remote commander to select “(3)
Write Bluetooth device address to Registry”.
13. Press the [ ] button on the remote commander, wait until the
display show “Status: Write Successful!” (Screen 5).
14. Press the [
@
/1
] button to turn the power off.
Diag
Diag
Category: Wireless LAN Test
Category: Wireless LAN Test
[2] Connect to AccessPoint
[3] Start Display RSSI Value
[4] Start Ping Test
[3] Start Display RSSI Value
[4] Start Ping Test
P2P device address: ee:0e:c4:18:43:d1
HELP: [UP] [DOWN] [ENT] [RET]
Status: Write Successful!
(Screen 1)
(Screen 2)
Category:
Wireless LAN Test
[1] Show WLAN HwInfo
(Screen 5)
Status: Write Successful!
Diag
Category: Bluetooth Device Test
(2) Bluetooth Disable
(3) Write Bluetooth device address to Registry
(4) Bluetooth Inquiry Test
Bluetooth Device address: EC:0E:C4:18:43:D2
HELP: [UP] [DOWN] [ENT] [RET]
(1) Bluetooth Enable
[5] Write P2P address to Registry
[6] P2P Registry Check
Diag
Diag
Category: Bluetooth Device Test
Category: Bluetooth Device Test
(2) Bluetooth Disable
(3) Write Bluetooth device address to Registry
(4) Bluetooth Inquiry Test
(3) Write Bluetooth device address to Registry
(4) Bluetooth Inquiry Test
HELP: [UP] [DOWN] [ENT] [RET]
(Screen 3)
(Screen 4)
Category:
Bluetooth Device Test
(1) Bluetooth Enable
Status: Bluetooth Enable Successful!
– Continued on next page –
Click on the first or last page to see other HT-ST9 service manuals if exist.