Read Sony HT-SF360 / HT-SS100 / HT-SS360 / STR-KS360 / STR-KS360S Service Manual online
STR-KS360/KS360S
10
SECTION 4
TEST MODE
1. COLD RESET
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. Press the [
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. Press the [
?/1
] button on the set to turn the power on.
2. Keeps pressing the [
?/1
] button on the set for about fi ve sec-
onds.
3. The message “CLEARED” appears, then the set turns off.
2. HOW TO ENTER THE TEST MODE
2. HOW TO ENTER THE TEST MODE
Note: The operation of the button of the following test modes is only a
remote commander.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the buttons in order of [DMPORT]
→ [RETURN] →
[ENTER]
→ [0] → [1] → [0] → [SOUND FIELD]
3. The message “TEST” appears, then enter the test menu.
4. Press the [
4. Press the [
?/1
] button to exit from the test mode.
3. PANEL TEST
3-1. Pattern check
Procedure:
1. Enter the test mode menu.
2. Press the [
3-1. Pattern check
Procedure:
1. Enter the test mode menu.
2. Press the [
↑]/[↓] buttons to select “PANEL”, and press the
[ENTER] button.
3. All segments and all LEDs turn on. Change as follows all on,
test pattern 1, test pattern 2, all on in this order.
3-2. Key check
Procedure:
1. Press the [VOLUME –] button, while executing pattern
Procedure:
1. Press the [VOLUME –] button, while executing pattern
check.
2. The message “K0 V0” appears. “K0” value increases when-
ever a button on the set is pressed. However, once a button has
been pressed, it is no longer taken into account. All buttons on
the set is pressed, “OK” and “K2” are alternately displayed.
been pressed, it is no longer taken into account. All buttons on
the set is pressed, “OK” and “K2” are alternately displayed.
3. “V” value increases in the manner of 0, 1, 2, 3 ... [MASTER
VOLUME] knob is turned clockwise, or it decreases in the
manner of 0, 9, 8, 7 ... [MASTER VOLUME] knob is turned
counterclockwise.
manner of 0, 9, 8, 7 ... [MASTER VOLUME] knob is turned
counterclockwise.
4. Press the [
?/1
] button to exit from the test mode.
3-3. Software version and destination display
Procedure:
1. Press the [VOLUME +] button, while executing pattern
check.
2. The display of model name, destination, and software version
changes whenever [VOLUME +] button is pressed.
3. Press the [
?/1
] button to exit from the test mode.
4. AMP TEST
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
5. TUNER FACTORY PRESET
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
6. VACS DISPLAY
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
7. VACS ON/OFF
Procedure:
1. Enter the test mode menu.
2. Press
Procedure:
1. Enter the test mode menu.
2. Press
the
[
↑]/[↓] buttons to select “VCS CTRL”, and press the
[ENTER] button.
3. VACS ON/OFF changes whenever this mode is decided.
(There is no change in the display)
8. DSP HALT MODE
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
9. DSP STATUS DISPLAY
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
10. HDMI UCOM UPDATE
Procedure:
1. Enter the test mode menu.
2. Press
Procedure:
1. Enter the test mode menu.
2. Press
the
[
↑]/[↓] buttons to select “HDMI VER”, and press the
[ENTER] button.
3. HDMI microprocessor software version is displayed.
4. Press the [
4. Press the [
?/1
] button to exit from the test mode.
11. DMPORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN1701) on the MAIN board.
2. Press the [
?/1
] button to turn the power on.
3. Confi rm that both LEDs of the DMPORT check jig lights.
(Confi rmation the power supply line)
4. Press the [DMPORT] button to select the “DMPORT”.
5. Enter the test mode menu.
6. Press
5. Enter the test mode menu.
6. Press
the
[
↑]/[↓] buttons to select the “DMP CHK”, and press
the [ENTER] button.
7. The message “DMPORTOK.” appears on the fl uorescent indi-
cator tube and enter the digital media port test mode. (Confi r-
mation of communication line)
mation of communication line)
When “NO DET” and “UART TO” are displayed on the fl uo-
rescent indicator tube, confi rm the connection of the DMPORT
check jig, and enter the mode again.
rescent indicator tube, confi rm the connection of the DMPORT
check jig, and enter the mode again.
Each time the [
>
] button is pressed, the connect check and
adaptor version check are changed.
Press the [
.
] button, connected confi rmation of the
DMPORT check jig is done again.
8. To a pin-jack of the DMPORT check jig input information rel-
evant to audio signal (sine-wave 1.0 Vrms).
9. Confi rm the output of speakers. (Confi rmation of analog sig-
nal)
10. Press the [
?/1
] button to exit from the test mode.
AF
oscillator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
set
FL/FR
speakers
speakers
MAIN board
CN1701
MAIN board
TB3002
12. DMPORT DEVICE TEST
Note: It connects with the iPod adaptor and it is necessary to repair hard-
ness to execute this mode.
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN1701) on the MAIN board.
2. Enter the test mode menu.
3. Press the [
3. Press the [
↑]/[↓] buttons to select “DMP DEV”, and press the
[ENTER] button.
4. LED on the jig lights.
5. Press the [
5. Press the [
?/1
] button to exit from the test mode.
Click on the first or last page to see other HT-SF360 / HT-SS100 / HT-SS360 / STR-KS360 / STR-KS360S service manuals if exist.