Read Sony HT-DDWG800 / STR-KG800 Service Manual online
STR-KG800
12
SECTION 4
TEST MODE
FL CHECK MODE
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. When pressing the [TUNING MODE] and [DISPLAY] but-
All fl uorescent segments are tested. When this test is activated, all
segments turn on at the same time, then each segment turns on one
after another.
Procedure:
1. When pressing the [TUNING MODE] and [DISPLAY] but-
tons, press the [
?/1
] button to turn on the main power.
2. All segments turn on.
MEMORY
L
C
R
SL
S
SR
SB SBR
SBL
SW
LFE
SP A
SP B
SP B
CAT
NEO:6
SAT
D.RANGE
RDS ST
MONO
DTS-ES
96 / 24
HDMI
COAX
D EX
OPT
PL II x
PL
dB
k Hz
mft.
MHz
3. Turn the [INPUT SELECTOR] dial.
4. Test pattern 1 turn on.
4. Test pattern 1 turn on.
L
R
S
LFE
SP B
NEO:6
SAT
D.RANGE
RDS ST
MONO
DTS-ES
HDMI
COAX
D EX
PL II x
k
m
MHz
5. Turn the [INPUT SELECTOR] dial once again.
6. Test pattern 2 turn on.
6. Test pattern 2 turn on.
MEMORY
C
SL
SR
SB SBR
SBL
SW
CAT
DTS
D
PL
dB
Hz
ft.
ST
7. Turn the [INPUT SELECTOR] dial once again. All segments
turn off.
8. Every turning of the [INPUT SELECTOR] dial turns on each
segment one after another on the same order.
S.F. CLEAR MODE
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [2CH] button, press the [
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [2CH] button, press the [
?/1
] button to turn
on the main power.
2. The message “S.F CLR.” appears and initialization is per-
formed.
VERSION CHECK MODE
When this mode is used the model, the destination and the software
version number are displayed.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [DISPLAY] but-
When this mode is used the model, the destination and the software
version number are displayed.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [DISPLAY] but-
tons, press the [
?/1
] button to turn on the main power.
2. The model, the distination and the software version number
appear.
KEY CHECK MODE
This mode is used to check the key.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [2CH] but-
This mode is used to check the key.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [2CH] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “REST 13” appears.
3. Every pressing of any button other than the [
3. Every pressing of any button other than the [
?/1
] button counts
down the buttons. The buttons which are already counted once
are not counted again.
are not counted again.
4. When all buttons are pressed, the message “REST 00” ap-
pears.
SWAP ALL MODE
When this mode is used, output the audio signal of front L/R chan-
nel to all channel.
Procedure:
1. While pressing the [MEMORY/ENTER] and [DISPLAY] but-
When this mode is used, output the audio signal of front L/R chan-
nel to all channel.
Procedure:
1. While pressing the [MEMORY/ENTER] and [DISPLAY] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “DSP TEST” appears.
3. Press the [AMP MENU] button on the remote commander, and
3. Press the [AMP MENU] button on the remote commander, and
the message “9_DSPTST” appears.
4. Press the [
b] button on the remote commander to enter the
DSP test mode menu.
5. Press the [
v] button on the remote commander twice to enter
the swap mode, and the message “SWP.AUTO” appears.
6. Press the [
b] button on the remote commander twice to select
“SWP.
[]ALL”.
SHIPMENT MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [MUSIC] but-
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [SPEAKERS (ON/OFF)] and [MUSIC] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears.
DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
DSP Data Line
Check
Start
Pass
Pass
Auto Cal Mic
Check
END
Factory Test System Setup
SPK Front Left
DCAC MIC
Receiver
1. When power off :
While pressing the [MEMORY/ENTER] and [MOVIE] but-
tons, press the [
tons, press the [
?/1
] button to turn on the main power.
“DCAC FTM” appears.
Afterward, press the [TUNING MODE] to start DCAC factory
test mode.
test mode.
Click on the first or last page to see other HT-DDWG800 / STR-KG800 service manuals if exist.