Read Sony HT-DDW990 / STR-K990 Service Manual online
SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
US Model
Canadian Model
MULTI CHANNEL AV RECEIVER
9-887-508-02
2008H16-1
© 2008.08
© 2008.08
Ver. 1.1 2008.08
SPECIFICATIONS
STR-K990
• STR-K990 is the tuner and the amplifier section
in HT-DDW990.
This receiver incorporates Dolby* Digital and Pro Logic Surround and
the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
the DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
** “DTS” and “DTS Digital Surround” are registered trademarks of
DTS, Inc.
— Continued on next page —
AUDIO POWER
SPECIFICATIONS
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
HARMONIC DISTORTION:
(Models of area code US only)
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than 1%
total harmonic distortion from 250 milliwatts
to rated output.
120 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than 1%
total harmonic distortion from 250 milliwatts
to rated output.
Amplifier section
Power Output
1)
Stereo mode (6 ohms, 1 kHz, THD 1%)
90 W + 90 W
Surround mode
2)
(reference) (6 ohms, 1 kHz,
THD 10%)
RMS output
FRONT:140 W
per channel
CENTER:140 W
SURROUND:140 W
per channel
1)
Measured under the following conditions:
2)
Reference power output for front, center and
surround speakers. Depending on the sound field
settings and the source, there may be no sound
output.
surround speakers. Depending on the sound field
settings and the source, there may be no sound
output.
Inputs
Analog
Sensitivity: 800 mV/
50 kohms
Digital (Coaxial) Impedance: 75 ohms
Outputs (Analog)
AUDIO OUT
Voltage: 800 mV/
10 kohms
SUB WOOFER
Voltage: 2 V/1 kohm
Tone
Gain levels
±
6 dB, 1 dB step
Area code
Power requirements
US, Canadian
120 V AC, 60 Hz
Reproduction frequency range:
28 – 20,000 Hz
FM tuner section
Tuning range
87.5 - 108.0 MHz
Antenna
FM wire antenna
Antenna terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
With 10-kHz tuning scale:
530 – 1,710 kHz
3)
With 9-kHz tuning scale:
531 – 1,710 kHz
3)
Antenna
Loop antenna
Intermediate frequency
450 kHz
3)
You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the
procedure.
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the
procedure.
2
STR-K990
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
Power consumption
Power consumption (during standby mode)
0.3 W
Dimensions (width/height/depth) (Approx.)
17
× 6 1/4 × 12 1/4 inches
(430
× 157.5 × 310 mm)
including projecting parts
and controls
and controls
Mass (Approx.)
17 lb 4 oz (7.8 kg)
Area code
Power consumption
US
200 W
Canadian
270 VA
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
: 0.7 Vp-p, 75 ohms
P
R
/C
R
: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
General
Power requirements
Power output (DIGITAL MEDIA PORT)
DC OUT:
5V, 700 mA
Area code
Power requirements
US, Canadian
120 V AC, 60 Hz
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
Fig. A.
Using an AC voltmeter to check AC leakage.
1.5 k
Ω
0.15
µ
F
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
Design and specifications are subject to change without notice.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
3
STR-K990
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
TABLE OF CONTENTS
1.
GENERAL
...................................................................
4
2.
TEST MODE
............................................................... 11
3.
ELECTRICAL ADJUSTMENT
............................. 13
4.
DIAGRAMS
................................................................. 14
4-1.
Block Diagram – MAIN Section – .................................. 15
4-2.
Block Diagram – DISPLAY/POWER Section – ............. 16
4-3.
Printed Wiring Board – DIGITAL Board (Side A) – ...... 17
4-4.
Printed Wiring Board – DIGITAL Board (Side B) – ...... 18
4-5.
Schematic Diagram – DIGITAL Board (1/5) – .............. 19
4-6.
Schematic Diagram – DIGITAL Board (2/5) – .............. 20
4-7.
Schematic Diagram – DIGITAL Board (3/5) – .............. 21
4-8.
Schematic Diagram – DIGITAL Board (4/5) – .............. 22
4-9.
Schematic Diagram – DIGITAL Board (5/5) – .............. 23
4-10. Printed Wiring Board – MAIN Board – ......................... 24
4-11. Schematic Diagram – MAIN Board (1/4) – ................... 25
4-12. Schematic Diagram – MAIN Board (2/4) – ................... 26
4-13. Schematic Diagram – MAIN Board (3/4) – ................... 27
4-14. Schematic Diagram – MAIN Board (4/4) – ................... 28
4-15. Printed Wiring Boards
4-11. Schematic Diagram – MAIN Board (1/4) – ................... 25
4-12. Schematic Diagram – MAIN Board (2/4) – ................... 26
4-13. Schematic Diagram – MAIN Board (3/4) – ................... 27
4-14. Schematic Diagram – MAIN Board (4/4) – ................... 28
4-15. Printed Wiring Boards
– DISPLAY Board, POWER KEY Board – .................... 29
4-16. Schematic Diagram
– DISPLAY Board, POWER KEY Board – .................... 30
4-17. Printed Wiring Boards
– STANDBY Board, DCDC Board – .............................. 31
4-18. Schematic Diagram
– STANDBY Board, DCDC Board – .............................. 32
4-19. Printed Wiring Boards
– DCAC Board, VIDEO3 Board – .................................. 33
4-20. Schematic Diagram
– DCAC Board, VIDEO3 Board – .................................. 34
4-21. Printed Wiring Boards
– VIDEO Board, HEADPHONE Board – ....................... 35
4-22. Schematic Diagram
– VIDEO Board, HEADPHONE Board – ....................... 36
4-23. Printed Wiring Board – HDMI SW Board – .................. 37
4-24. Schematic Diagram – HDMI SW Board – ..................... 38
4-24. Schematic Diagram – HDMI SW Board – ..................... 38
5.
EXPLODED VIEWS
5-1.
Front Panel Section ......................................................... 47
5-2.
Chassis Section ................................................................ 48
6.
ELECTRICAL PARTS LIST
.................................. 49
About area codes
Th
Moreover, it is possible to distinguish the model
by Part No..
by Part No..
e area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
(see the illustration below).
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
ERS
ONT A
R
SURROUND
L
L
R
CENTER
Area code
Part No.
BACK PANEL
Model
Part No.
US Model
2-897-800-7
Canadian Model
2-897-800-8
4
STR-K990
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Front panel
.
Receiver
?/1
AUTO CAL MIC
SPEAKERS
(OFF/A/B/A+B)
PHONES
VIDEO 3 IN/PORTABLE AV IN
VIDEO
L AUDIO R
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
DISPLAY
INPUT MODE
INPUT SELECTOR
MASTER VOLUME
3
4
8
9
1 2
5
6
7
q;
qa
qj
qs
qg
qh
qd
qf
Name
Function
A
?
/
1
(on/standby)
Press to turn the receiver on
or off (page 29, 38, 39, 54).
or off (page 29, 38, 39, 54).
B
SPEAKERS
(OFF/A/B/A+B)
(OFF/A/B/A+B)
Press to select the speaker
system (page 30).
system (page 30).
C
Display
The current status of the
selected component or a list
of selectable items appears
here (page 7).
selected component or a list
of selectable items appears
here (page 7).
D
Remote sensor
Receives signals from
remote commander.
remote commander.
E
DISPLAY
Press to select information
displayed on the display
(page 63).
displayed on the display
(page 63).
F
INPUT MODE
Press to select the input
mode when the same
components are connected
to both digital and analog
jacks (page 59).
mode when the same
components are connected
to both digital and analog
jacks (page 59).
G
MASTER
VOLUME
VOLUME
Turn to adjust the volume
level of all speakers at the
same time (page 35, 36, 38,
39).
level of all speakers at the
same time (page 35, 36, 38,
39).
H
MUTING
Press to mute the sound
(page 36).
(page 36).
I
AUTO CAL
Press to activate the Auto
Calibration function (page
32).
Calibration function (page
32).
J
INPUT
SELECTOR
SELECTOR
Turn to select the input
source to playback (page
36).
source to playback (page
36).
Name
Function
K
2CH
Press to select a sound field
(page 49, 51, 54).
(page 49, 51, 54).
A.F.D.
MOVIE
MUSIC
L
TUNING +/–
Press to scan a station (page
55, 58).
55, 58).
M
TUNING MODE
Press to select the tuning
mode (page 55, 58).
mode (page 55, 58).
N
MEMORY/
ENTER
ENTER
Press to store a station or
enter the selection when
selecting the settings (page
29, 57).
enter the selection when
selecting the settings (page
29, 57).
O
VIDEO 3 IN/
PORTABLE AV
IN jacks
PORTABLE AV
IN jacks
Connects to a camcorder or
video game (page 27, 36).
video game (page 27, 36).
P
AUTO CAL MIC
jack
jack
Connects to the supplied
optimizer microphone for
the Auto Calibration
function (page 31).
optimizer microphone for
the Auto Calibration
function (page 31).
Q
PHONES jack
Connects to headphones
(page 73).
(page 73).
