HT-DDW680, HT-DDW780, HTP-36DW, STR-K680, STR-K780 - Sony Audio Service Manual (repair manual). Page 3

Read Sony HT-DDW680 / HT-DDW780 / HTP-36DW / STR-K680 / STR-K780 Service Manual online

3
STR-K680/K780
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1.
GENERAL
...................................................................
4
2.
TEST MODE
............................................................... 11
3.
DIAGRAMS
3-1.
Block Diagram – MAIN Section – .................................. 14
3-2.
Block Diagram – DISPLAY/POWER Section – ............. 15
3-3.
Printed Wiring Board  – DIGITAL Board (Side A) – ...... 16
3-4.
Printed Wiring Board  – DIGITAL Board (Side B) – ...... 17
3-5.
Schematic Diagram  – DIGITAL Board (1/3) – .............. 18
3-6.
Schematic Diagram  – DIGITAL Board (2/3) – .............. 19
3-7.
Schematic Diagram  – DIGITAL Board (3/3) – .............. 20
3-8.
Printed Wiring Board  – MAIN Board – ......................... 21
3-9.
Schematic Diagram  – MAIN Board (1/3) – ................... 22
3-10. Schematic Diagram  – MAIN Board (2/3),
HEADPHONE Board – ................................................... 23
3-11. Schematic Diagram  – MAIN Board (3/3),
AC SELECT Board, ADCC Board,
STANDBY Board – ......................................................... 24
3-12. Printed Wiring Boards
– ADCC Board, HEADPHONE Board – ........................ 25
3-13. Printed Wiring Boards
– STANDBY Board, AC SELECT Board – .................... 26
3-14. Printed Wiring Board  – DISPLAY Board – ................... 27
3-15. Printed Wiring Boards
– TUNING Board, POWER Board – .............................. 28
3-16. Schematic Diagram  – DISPLAY Board,
TUNING Board, POWER Board – ................................. 29
3-17. Printed Wiring Board  – VIDEO Board – ........................ 30
3-18. Schematic Diagram  – VIDEO Board – .......................... 31
4.
EXPLODED VIEWS
4-1.
Front Panel Section ......................................................... 39
4-2.
Chassis Section ................................................................ 40
5.
ELECTRICAL PARTS LIST
.................................. 41
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS  IDENTIFIED  BY  MARK  
0
  OR  DOTTED  LINE
WITH  MARK  
0
  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS  WHOSE
PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  MANUAL  OR
IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
Page of 52
Display

Click on the first or last page to see other HT-DDW680 / HT-DDW780 / HTP-36DW / STR-K680 / STR-K780 service manuals if exist.